{"title":"Ender Mods","description":"","products":[{"product_id":"mean-well-lrs-350-24","title":"Mean Well LRS-350-24 - 350W 24V 14.6A Power Supply (Voron \/ Klipper)","description":"\u003ch2\u003eMean Well LRS-350-24 — 350W 24V 14.6A enclosed switching PSU\u003c\/h2\u003e\n\u003cp\u003eThis is the workhorse 24V supply for a Voron, RatRig, or any Klipper-driven machine. At 24Vdc and 14.6A (350.4W) it has the headroom to run a mains-class build's full DC side: the bed heater, the control board and steppers, the hotend cartridge, and the part-cooling and electronics fans — all from one brick. 24V is the Voron standard because it lets the bed heater and motors pull current at half the amperage 12V would need, which keeps wire gauge and connector heating sane.\u003c\/p\u003e\n\n\u003ch3\u003eWhat it powers\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBed heater\u003c\/strong\u003e — a 24V silicone\/PCB bed heater is the biggest single load; the LRS-350-24's 14.6A continuous rating covers a 200×200 to 300×300 bed plus everything else without sitting at 100%.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eControl board + steppers + hotend\u003c\/strong\u003e — SKR, Octopus, BTT, Spider-class boards take 24V in and regulate down for the MCU and drivers. The hotend heater cartridge runs straight off the 24V rail.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFans and accessories\u003c\/strong\u003e — 24V fans wire directly; 5V accessories (Raspberry Pi \/ SBC) need a separate 5V supply or a buck converter — do not run a Pi off this unit's 24V rail directly.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eThe wiring and safety reality (read this)\u003c\/h3\u003e\n\u003cp\u003eThis is a \u003cstrong\u003ebare-terminal mains supply\u003c\/strong\u003e. The left-hand screw terminals are live AC: L, N, and earth (⏚). You are responsible for everything upstream of them:\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSet the voltage switch first.\u003c\/strong\u003e The 115\/230 slide switch must match your wall voltage. On 230V mains with the switch left at 115, you will destroy the unit instantly. North America = 115; most of Europe\/AU = 230.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFuse the mains side.\u003c\/strong\u003e Use a fused, switched IEC inlet or an inline fuse on L. The LRS has internal protection on its outputs, not branch-circuit protection on its input.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBond earth.\u003c\/strong\u003e The metal case must connect to mains earth at the ⏚ terminal. This is not optional on a metal-frame printer.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCover the terminals.\u003c\/strong\u003e Exposed mains screw terminals belong inside an enclosed electronics bay with a terminal cover or shroud — never reachable while powered.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eStrain-relief and ferrule.\u003c\/strong\u003e Ferrule the stranded conductors and strain-relieve both the mains cord and the DC leads so a tug can't back a wire out of a terminal.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIf you're not comfortable terminating mains wiring to screw terminals, this is the part to slow down on or get a second set of eyes for. The DC side (24V V+\/V−) is harmless to handle; the AC side is not.\u003c\/p\u003e\n\n\u003ch3\u003eWhy this form factor\u003c\/h3\u003e\n\u003cp\u003eThe LRS series is the slim 30mm enclosed family — the volume baseline that most Voron\/Klipper kits are designed around, and the cheapest way into a clean 24V build. It is \u003cem\u003enot\u003c\/em\u003e dead-silent: the 350W tier carries a small thermostatic fan that only spins when the internal sensor crosses ~50°C, so under light printing loads it typically stays off and runs on convection. If you want a guaranteed-fanless or DIN-rail-clean install, that's the HDR (ultra-slim DIN rail) or UHP (slim, PFC, premium) families — they comp higher than this one. For a standard enclosed bay mount at the best price, the LRS-350-24 is the right call.\u003c\/p\u003e\n\n\u003ch3\u003eKey specs\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eOutput: 24Vdc, 14.6A, 350.4W\u003c\/li\u003e\n  \u003cli\u003eInput: 90–132 \/ 180–264VAC switch-selectable (85–264VAC), 240–370VDC, 47–63Hz\u003c\/li\u003e\n  \u003cli\u003eEfficiency: 88% typ.\u003c\/li\u003e\n  \u003cli\u003eSize: 215 × 115 × 30 mm\u003c\/li\u003e\n  \u003cli\u003eTemp: −25 to +70°C operating (derate above 50°C)\u003c\/li\u003e\n  \u003cli\u003eProtections: OVP 28.8–33.6V, overload 110–140%, OTP — all hiccup\/auto-recover\u003c\/li\u003e\n  \u003cli\u003eSafety: IEC\/UL 62368-1, overvoltage category III, altitude to 5000m\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOn sale as a clearance item — same part, same Mean Well datasheet, lower price.\u003c\/p\u003e","brand":"MEAN WELL USA Inc.","offers":[{"title":"Default Title","offer_id":43167953846494,"sku":"3481705586","price":33.74,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/LRS-350_DSL.jpg?v=1658721674"},{"product_id":"klackender-probe-by-kevinakasam","title":"KlackEnder Probe by kevinakasam","description":"\u003cp\u003eFrom the \u003ca title=\"KlackEnder-Probe GitHub\" href=\"https:\/\/github.com\/kevinakasam\/KlackEnder-Probe\" target=\"_blank\"\u003erepo\u003c\/a\u003e:\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003eWhat is This About?\u003c\/h3\u003e\n\u003cp\u003eAdaptation of the \u003ca title=\"Klicky-Probe github link\" href=\"https:\/\/github.com\/jlas1\/Klicky-Probe\" target=\"_blank\"\u003eKlicky\u003c\/a\u003e\/\u003ca title=\"Quickdraw_Probe github link\" href=\"https:\/\/github.com\/Annex-Engineering\/Quickdraw_Probe\" target=\"_blank\"\u003eQuickdraw\u003c\/a\u003e Probe for the Ender 3 and comparable Creality printers. The probe is compatible with all printers that use the X plate of the Ender 3 and cost of the probe is \u0026lt;10€, of which the switch is the most expensive part. The probe is compatible with Marlin and Klipper. Both firmwares work with the G29 command, the docking is done automatically by the printer, it couldn't be easier! Both firmwares add a KlackEnder menu to the display that can be used to dock and undock the Probe. The Bed-Mesh can be created via the custom menu, via the default firmware settings or with G29.\u003c\/p\u003e\n\u003cp\u003eMore info may be found in the \u003ca title=\"KlackEnder-Probe GitHub\" href=\"https:\/\/github.com\/kevinakasam\/KlackEnder-Probe\" target=\"_blank\"\u003erepo\u003c\/a\u003e and extremely well documented on \u003ca title=\"kevinakasam.com\" href=\"https:\/\/kevinakasam.com\" target=\"_blank\"\u003ekevinakasam.com\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch4\u003eWhat's in the Kit?\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eJST-XH 2 Pin Housing x 1\u003c\/li\u003e\n\u003cli\u003eJST-XH 3 Pin Housing x 1\u003c\/li\u003e\n\u003cli\u003eJST-XH Female Pins x 6\u003c\/li\u003e\n\u003cli\u003eM5 T-Nut x 2\u003c\/li\u003e\n\u003cli\u003eM2x10 Self Tapping Screws for Plastic x 2\u003c\/li\u003e\n\u003cli\u003eM2x12 \u003cspan data-mce-fragment=\"1\"\u003eSelf Tapping Screws for Plastic x 2\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eOmron D2F-x Microswitch\u003c\/li\u003e\n\u003cli\u003e1.5m 24AWG FEP Wire\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eZip-Tie 2x100mm x 3\u003c\/li\u003e\n\u003cli\u003eM3x10 BHCS x 1\u003c\/li\u003e\n\u003cli\u003eM3x12-16 BHCS x 1\u003c\/li\u003e\n\u003cli\u003eM5x8 BHCS x 2\u003c\/li\u003e\n\u003cli\u003eM6x3mm Round magnets x 6\u003c\/li\u003e\n\u003cli\u003eM5x45 SHCS x 1\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dfh.fm","offers":[{"title":"Black Oxide Coated Steel","offer_id":44802377679070,"sku":"6547110744","price":8.99,"currency_code":"USD","in_stock":false},{"title":"Black Nickel Coated Stainless Steel","offer_id":44802377711838,"sku":"6547110745","price":9.99,"currency_code":"USD","in_stock":true},{"title":"Stainless Steel","offer_id":44802377744606,"sku":"6547110746","price":8.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/ender_klicky_klack.jpg?v=1675420014"},{"product_id":"beltdrivenender3-kit-by-kevinakasam","title":"BeltDrivenEnder3 Kit by kevinakasam","description":"\u003cp\u003e\u003cstrong\u003eWhat comes in the kit\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003eSingle Z:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e20T 8mm bore 6mm width pulley by \u003cstrong\u003eRunice\u003c\/strong\u003e x 3\u003c\/li\u003e\n\u003cli\u003e16T 5mm bore 6mm width pulley by \u003cstrong\u003eRunice\u003c\/strong\u003e x 1\u003c\/li\u003e\n\u003cli\u003eLL-2GT-6 RF belt by \u003cstrong\u003eGates\u003c\/strong\u003e x 2m\u003c\/li\u003e\n\u003cli\u003e188mm RF belt Loop by \u003cstrong\u003eGates\u003c\/strong\u003e x 1\u003c\/li\u003e\n\u003cli\u003eF623-RS bearing by \u003cstrong\u003eRS\u003c\/strong\u003e x 4\u003c\/li\u003e\n\u003cli\u003e608 bearing by \u003cstrong\u003eRS\u003c\/strong\u003e x 5\u003c\/li\u003e\n\u003cli\u003eG6 stainless steel or black anodized aluminum M3x14mm pin by \u003cstrong\u003eDFH\u003c\/strong\u003e x 2\u003c\/li\u003e\n\u003cli\u003eG6\u003cmeta charset=\"UTF-8\"\u003e \u003cspan data-mce-fragment=\"1\"\u003estainless \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003es\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eteel\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003e or \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eb\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003elack \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003ea\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003enodized \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003ea\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eluminum \u003c\/span\u003eM8x355mm Shaft by \u003cstrong\u003eDFH\u003c\/strong\u003e x 1\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eDual Z:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e20T 8mm bore 6mm width pulley by \u003cstrong\u003eRunice\u003c\/strong\u003e x 4\u003c\/li\u003e\n\u003cli\u003e16T 5mm bore 6mm width pulley by \u003cstrong\u003eRunice\u003c\/strong\u003e x 2\u003c\/li\u003e\n\u003cli\u003eLL-2GT-6 RF Belt by \u003cstrong\u003eGates\u003c\/strong\u003e x 2m\u003c\/li\u003e\n\u003cli\u003e188mm RF belt Loop by \u003cstrong\u003eGates\u003c\/strong\u003e x 2\u003c\/li\u003e\n\u003cli\u003eF623-RS bearing by \u003cstrong\u003eRS\u003c\/strong\u003e x 4\u003c\/li\u003e\n\u003cli\u003e608 bearing by \u003cstrong\u003eRS\u003c\/strong\u003e x 5\u003c\/li\u003e\n\u003cli\u003eG6\u003cmeta charset=\"UTF-8\"\u003e \u003cspan data-mce-fragment=\"1\"\u003estainless \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003es\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eteel\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003e or \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eb\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003elack \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003ea\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003enodized \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003ea\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eluminum \u003c\/span\u003eM3x14mm pin by \u003cstrong\u003eDFH\u003c\/strong\u003e x 2\u003c\/li\u003e\n\u003cli\u003eG6\u003cmeta charset=\"UTF-8\"\u003e \u003cspan data-mce-fragment=\"1\"\u003estainless \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003es\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eteel\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003e or \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eb\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003elack \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003ea\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003enodized \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003ea\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eluminum \u003c\/span\u003eM8x65mm Shaft by \u003cstrong\u003eDFH\u003c\/strong\u003e x 2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eMore information may be found on \u003ca href=\"https:\/\/github.com\/kevinakasam\/BeltDrivenEnder3\" title=\"BeltDrivenEnder3 GitHub link\" target=\"_blank\"\u003eGitHub\u003c\/a\u003e or, build yours, interactively, on \u003ca href=\"https:\/\/kevinakasam.com\" title=\"kevinakasam.com\" target=\"_blank\"\u003ekevinakasam.com\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003csmall\u003eNote: Silver kits are currently shipping with black aluminum 3mm pins.\u003c\/small\u003e\u003c\/p\u003e","brand":"dfh.fm","offers":[{"title":"Single Z \/ Black","offer_id":43963792687326,"sku":"1983087836","price":44.99,"currency_code":"USD","in_stock":true},{"title":"Single Z \/ Silver","offer_id":43967153144030,"sku":"2448127943","price":39.99,"currency_code":"USD","in_stock":false},{"title":"Dual Z \/ Black","offer_id":43963792785630,"sku":"3408514150","price":46.99,"currency_code":"USD","in_stock":true},{"title":"Dual Z \/ Silver","offer_id":43967153209566,"sku":"9094330393","price":44.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/26DD65FB-FDE5-4A22-8D0B-8CB8B5A96CE6_1_201_a.jpg?v=1677744731"},{"product_id":"beltdrivenender3-linear-rails-kit-by-kevinakasam","title":"BeltDrivenEnder3 by kevinakasam 440C Stainless Steel Linear Rails Kit","description":"\u003cp\u003eI realize, coming from the Ender ecosystem, this may seem like a crazy price for rails, but you really do get what you pay for. Suck it up. Future you will be glad you did. \u003c\/p\u003e\n\u003cp\u003eKit includes 2 x 300mm MGN12H 440c Linear Rails by DFH.\u003c\/p\u003e","brand":"dfh.fm","offers":[{"title":"Default Title","offer_id":43967492325598,"sku":"8415250126","price":60.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/IMG_3959.jpg?v=1675522320"},{"product_id":"fastener-kit-for-beltdrivenender3","title":"Fastener Kit for BeltDrivenEnder3 by kevinakasam","description":"\u003cp\u003eKit includes:\u003c\/p\u003e\n\u003ctable\u003e\n    \u003cthead\u003e\n        \u003ctr\u003e\n            \u003cth\u003eItem\u003c\/th\u003e\n            \u003cth\u003eRecommended\u003c\/th\u003e\n            \u003cth\u003eIncluded\u003c\/th\u003e\n        \u003c\/tr\u003e\n    \u003c\/thead\u003e\n    \u003ctbody\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM5x40\u003c\/td\u003e\n            \u003ctd\u003e6\u003c\/td\u003e\n            \u003ctd\u003e8\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM5x30\u003c\/td\u003e\n            \u003ctd\u003e1\u003c\/td\u003e\n            \u003ctd\u003e2\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM5x8\u003c\/td\u003e\n            \u003ctd\u003e28\u003c\/td\u003e\n            \u003ctd\u003e34\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3x25\u003c\/td\u003e\n            \u003ctd\u003e2\u003c\/td\u003e\n            \u003ctd\u003e3\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3x20\u003c\/td\u003e\n            \u003ctd\u003e4\u003c\/td\u003e\n            \u003ctd\u003e5\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3x12\u003c\/td\u003e\n            \u003ctd\u003e8\u003c\/td\u003e\n            \u003ctd\u003e10\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3x10\u003c\/td\u003e\n            \u003ctd\u003e8\u003c\/td\u003e\n            \u003ctd\u003e10\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3x8\u003c\/td\u003e\n            \u003ctd\u003e32\u003c\/td\u003e\n            \u003ctd\u003e39\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3x6\u003c\/td\u003e\n            \u003ctd\u003e10\u003c\/td\u003e\n            \u003ctd\u003e13\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM5 lock-nut\u003c\/td\u003e\n            \u003ctd\u003e7\u003c\/td\u003e\n            \u003ctd\u003e9\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3 nuts\u003c\/td\u003e\n            \u003ctd\u003e14\u003c\/td\u003e\n            \u003ctd\u003e17\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3 washer\u003c\/td\u003e\n            \u003ctd\u003e4\u003c\/td\u003e\n            \u003ctd\u003e5\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM5 T-nuts\u003c\/td\u003e\n            \u003ctd\u003e28\u003c\/td\u003e\n            \u003ctd\u003e34\u003c\/td\u003e\n        \u003c\/tr\u003e\n        \u003ctr\u003e\n            \u003ctd\u003eM3 T-nuts\u003c\/td\u003e\n            \u003ctd\u003e24\u003c\/td\u003e\n            \u003ctd\u003e30\u003c\/td\u003e\n        \u003c\/tr\u003e\n    \u003c\/tbody\u003e\n\u003c\/table\u003e","brand":"dfh.fm","offers":[{"title":"Stainless Steel","offer_id":44122573766878,"sku":"4364800416","price":19.99,"currency_code":"USD","in_stock":false},{"title":"Black Oxide Coated Steel","offer_id":44122573832414,"sku":"3853197619","price":19.99,"currency_code":"USD","in_stock":false},{"title":"Black Nickel Coated Stainless Steel","offer_id":44802404221150,"sku":"","price":22.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/yghfhg.jpg?v=1675523397"},{"product_id":"15mil-ultem-black-pei-sheets","title":"15Mil Ultem® Black PEI Sheets With 3M Adhesive Tape","description":"\u003cp\u003eIndividual black PEI sheets.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThickness\u003c\/strong\u003e:0.15mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMax sustained temp\u003c\/strong\u003e: 149 °C\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eUltem®\/PEI (polyetherimide) film offers high heat resistance, coupled with high mechanical strength, stiffness, UV stability, and broad chemical resistance. This combination of properties proves the ability of this film to be used for a wide variety of demanding new design concepts. Similar to PEEK, Ultem® can be considered a more cost effective solution if continuous temperatures below 338F are acceptable per the application. It has a UL94 flame resistance rating of VTM-0, is FDA compliant, and is thermoformable.\u003c\/p\u003e","brand":"dfh.fm","offers":[{"title":"250mm x 250mm","offer_id":44839036125406,"sku":"1929285304","price":9.99,"currency_code":"USD","in_stock":true},{"title":"265mm x 265mm","offer_id":44098597617886,"sku":"5884588335","price":12.99,"currency_code":"USD","in_stock":false},{"title":"315mm x 315mm","offer_id":44098597650654,"sku":"8802132239","price":15.99,"currency_code":"USD","in_stock":false},{"title":"365mm x 365mm","offer_id":44098597683422,"sku":"2386301711","price":18.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/Untitled15_1de348fb-b031-4912-aa94-53bcf2dd6d22.png?v=1696570017"},{"product_id":"beltdrivenender3-linear-rails-kit-by-kevinakasam-black-steel","title":"BeltDrivenEnder3 by kevinakasam Black Steel Linear Rails Kit","description":"\u003cp\u003e\u003cstrong\u003eBlack-steel Z-axis linear rail pair for the BeltDrivenEnder3 mod.\u003c\/strong\u003e This kit supplies the two \u003cstrong\u003e300 mm MGN12H\u003c\/strong\u003e rails with \u003cstrong\u003eZ0 preload\u003c\/strong\u003e used when adding linear rails to kevinakasam’s BeltDrivenEnder3-style Ender 3 Z-axis build.\u003c\/p\u003e\n\u003ch3\u003eWhy use these rails\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMatched pair:\u003c\/strong\u003e two 300 mm MGN12H rail-and-carriage assemblies for the left and right Z sides.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eZ0 preload:\u003c\/strong\u003e light preload for smooth motion where low drag matters more than heavy machine-tool loading.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBlack steel option:\u003c\/strong\u003e a lower-cost alternative to the \u003ca href=\"https:\/\/dfh.fm\/products\/beltdrivenender3-linear-rails-kit-by-kevinakasam\"\u003e440C stainless BeltDrivenEnder3 rail kit\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eQuantity: \u003cstrong\u003e2 rails\u003c\/strong\u003e, each with MGN12H carriage\u003c\/li\u003e\n  \u003cli\u003eRail length: \u003cstrong\u003e300 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eRail size: \u003cstrong\u003eMGN12H\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003ePreload: \u003cstrong\u003eZ0\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eMaterial \/ finish: \u003cstrong\u003eblack steel\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eIntended for Ender 3-family BeltDrivenEnder3 builds based on kevinakasam’s open-source mod, which converts the Ender 3 Z axis from a leadscrew to synchronized belts. The official project notes compatibility with Ender 3, Ender 3 V2, and Ender 3 Pro; it is not for Ender 3 S1.\u003c\/p\u003e\n\u003ch3\u003ePairs with\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003ca href=\"https:\/\/dfh.fm\/products\/beltdrivenender3-kit-by-kevinakasam\"\u003eBeltDrivenEnder3 Kit by kevinakasam\u003c\/a\u003e for the core conversion hardware.\u003c\/li\u003e\n  \u003cli\u003e\n\u003ca href=\"https:\/\/dfh.fm\/products\/fastener-kit-for-beltdrivenender3\"\u003eFastener Kit for BeltDrivenEnder3\u003c\/a\u003e if you are gathering the project hardware separately.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat this is not\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eNot the complete BeltDrivenEnder3 conversion kit — belts, printed parts, fasteners, bearings, rods, and electronics are not included unless separately purchased.\u003c\/li\u003e\n  \u003cli\u003eNot stainless steel. Choose the 440C stainless version if corrosion resistance is the priority; keep black-steel rails clean, lubricated, and dry.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dfh.fm","offers":[{"title":"Default Title","offer_id":44122613711070,"sku":"4862185192","price":50.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/sfggsfgdf.jpg?v=1680298864"},{"product_id":"kevinakasam-keychains","title":"kevinakasam Keychains","description":"\u003cp\u003e\u003cstrong\u003eKevinAkaSam steel logo keychain\u003c\/strong\u003e for builders who want a small piece of maker swag with their keys, tool bag, or printer case. Choose black-coated steel or brushed silver steel.\u003c\/p\u003e\n\u003ch3\u003eWhy this one\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSquare steel keychain with the cut-through KevinAkaSam logo.\u003c\/li\u003e\n\u003cli\u003eTwo finish options: \u003cstrong\u003eblack steel\u003c\/strong\u003e or \u003cstrong\u003ebrushed silver steel\u003c\/strong\u003e.\u003c\/li\u003e\n\u003cli\u003eFlat, compact profile that fits a key ring, zipper pull, tool bag, or printer-accessory pouch.\u003c\/li\u003e\n\u003cli\u003eA simple add-on for fans of KevinAkaSam projects like the \u003ca href=\"https:\/\/dfh.fm\/products\/beltdrivenender3-kit-by-kevinakasam\"\u003eBeltDrivenEnder3 kit\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/klackender-probe-by-kevinakasam\"\u003eKlackEnder Probe\u003c\/a\u003e, and \u003ca href=\"https:\/\/dfh.fm\/products\/wth-burner-by-kevinakasam\"\u003eWTH-Burner\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eProduct: KevinAkaSam logo keychain\u003c\/li\u003e\n\u003cli\u003eMaterial: \u003cstrong\u003esteel\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eFinish options: \u003cstrong\u003eblack\u003c\/strong\u003e or \u003cstrong\u003ebrushed silver\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eDesign: square plate with logo cutout and key-ring hole\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIntended use\u003c\/h3\u003e\n\u003cp\u003eThis is maker swag, not a printer component: use it as a keychain, bag tag, zipper pull, or small gift for someone building around KevinAkaSam’s 3D-printer projects.\u003c\/p\u003e\n\u003ch3\u003eDecision guide\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eChoose \u003cstrong\u003eBlack\u003c\/strong\u003e for a coated, low-profile look.\u003c\/li\u003e\n\u003cli\u003eChoose \u003cstrong\u003eBrushed Silver\u003c\/strong\u003e if you want the bare-metal finish to show.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNot a functional printer part, BOM component, or motion-system replacement.\u003c\/li\u003e\n\u003cli\u003eKey ring hardware is not shown in the product photos; this listing is for the steel logo keychain shown.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cblockquote\u003e“Have had this on my keys for 7 months and the coating is still almost completely unscathed, looks nice.”\u003c\/blockquote\u003e","brand":"dfh.fm","offers":[{"title":"Steel \/ Black","offer_id":44125693411550,"sku":"3426448633","price":7.99,"currency_code":"USD","in_stock":true},{"title":"Steel \/ Brushed Silver","offer_id":44125693444318,"sku":"6879184297","price":7.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/kevinakasamkeychains.jpg?v=1680550992"},{"product_id":"beltdrivenender3-by-kevinakasam-linear-rails-kit","title":"BeltDrivenEnder3 by kevinakasam Linear Rails Set","description":"\u003cp\u003e\u003cstrong\u003eDrop-in rail pair for the BeltDrivenEnder3 MGN Z conversion.\u003c\/strong\u003e This set includes two \u003cstrong\u003e300mm MGN12H linear rails\u003c\/strong\u003e with \u003cstrong\u003eZ0 preload\u003c\/strong\u003e, sized for the KevinAkaSam BeltDrivenEnder3 linear-rail Z-axis variant.\u003c\/p\u003e\n\u003ch3\u003eWhy use this set\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCorrect format:\u003c\/strong\u003e MGN12H rail and carriage format for the project’s MGN-12H variant.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMatched Z pair:\u003c\/strong\u003e two 300mm rails for the left and right Z uprights.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTwo material choices:\u003c\/strong\u003e Black Steel for the value build, or 440C Stainless Steel when corrosion resistance matters more.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProject fit:\u003c\/strong\u003e intended for the \u003ca href=\"https:\/\/dfh.fm\/products\/beltdrivenender3-kit-by-kevinakasam\"\u003eBeltDrivenEnder3 by KevinAkaSam\u003c\/a\u003e conversion when you are building the MGN rail version instead of the stock V-wheel version.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIncluded: \u003cstrong\u003e2 × MGN12H linear rails with carriages\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eRail length: \u003cstrong\u003e300mm\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003ePreload: \u003cstrong\u003eZ0\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eAxis\/use: \u003cstrong\u003eZ-axis rail conversion\u003c\/strong\u003e for BeltDrivenEnder3\u003c\/li\u003e\n  \u003cli\u003eVariant options: \u003cstrong\u003eBlack Steel\u003c\/strong\u003e or \u003cstrong\u003e440C Stainless Steel\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFor the KevinAkaSam BeltDrivenEnder3 V3 MGN-12H rail files. The project supports Ender 3-family machines except the S1; confirm your printed parts and frame setup before ordering.\u003c\/p\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eNot the full belt-driven Z conversion kit; pair with the \u003ca href=\"https:\/\/dfh.fm\/products\/beltdrivenender3-kit-by-kevinakasam\"\u003emain BeltDrivenEnder3 kit\u003c\/a\u003e and the \u003ca href=\"https:\/\/dfh.fm\/products\/fastener-kit-for-beltdrivenender3\"\u003eBeltDrivenEnder3 fastener kit\u003c\/a\u003e as needed.\u003c\/li\u003e\n  \u003cli\u003eNot a cure for extrusion inconsistency or tuning problems; KevinAkaSam specifically calls those out as separate printer-tuning issues.\u003c\/li\u003e\n  \u003cli\u003eRails need cleaning and lubrication. The project author recommends the wheel version first unless you specifically want the rail build.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cblockquote\u003e“High quality. No grit came out when I had these in the ultrasonic cleaner in solvent.”\u003c\/blockquote\u003e","brand":"dfh.fm","offers":[{"title":"Black Steel","offer_id":44186689011934,"sku":"4862185192","price":49.99,"currency_code":"USD","in_stock":true},{"title":"440c Stainless Steel","offer_id":44186689044702,"sku":"8415250126","price":59.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/IMG_3959_fee6a378-7070-465d-ac13-73aff958b27c.jpg?v=1683919886"},{"product_id":"8x20mm-light-load-spring-black","title":"Black Bed-Leveling Die Springs - Light-Load 8x4x20mm | Voron \/ Printers for Ants \/ Ender","description":"\u003ch2\u003eThe yellow spring spec — finally in black.\u003c\/h2\u003e\n\u003cp\u003eThe spring your printer wants for bed leveling isn't defined by its color — it's defined by its \u003cstrong\u003eload class\u003c\/strong\u003e. Industrial die springs are color-coded by rated force, and the correct class for a heated print bed is the \u003cstrong\u003elight-load\u003c\/strong\u003e spring — the one normally sold in \u003cem\u003eyellow\u003c\/em\u003e. Too stiff and it fights your leveling screws; too soft (like the springs in your kit) and your bed drifts out of level after every few prints.\u003c\/p\u003e\n\u003cp\u003eWe had these printer-grade light-load die springs \u003cstrong\u003ecustom-manufactured in black\u003c\/strong\u003e — identical spec, blacked-out finish — so your stealth build stays stealth. Same engineering. No yellow pop under the bed.\u003c\/p\u003e\n\u003ch3\u003eWhy this is an upgrade, not just a color swap\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConsistent, repeatable tension.\u003c\/strong\u003e Engineered die springs hold preload across hundreds of print hours; soft stock springs lose tension fast.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHolds your bed level.\u003c\/strong\u003e A firm, defined spring rate resists the vibration that walks leveling knobs loose — so you re-level far less often.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDoesn't sag under heat.\u003c\/strong\u003e Heat-rated spring steel holds its force at bed temps where cheap springs relax and compress permanently.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlat, ground ends.\u003c\/strong\u003e Square-ground faces seat flush and load the bed at a true 90° — no rocking, no shift between prints.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFits everything\u003c\/h3\u003e\n\u003cp\u003eOne spring, every machine. \u003cstrong\u003e8mm OD x 4mm ID x 20mm\u003c\/strong\u003e clears a standard M4 leveling screw:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoron\u003c\/strong\u003e V0, Trident, V2.4 (and Switchwire)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrinters for Ants\u003c\/strong\u003e — Micron and others\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCreality\u003c\/strong\u003e Ender 3 \/ Pro \/ V2 \/ 5, CR-10 series — and most beds using 8x20mm leveling springs\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow many do I need?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eVoron V0 \u0026amp; Trident — \u003cstrong\u003e3 springs\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eVoron V2.4 — \u003cstrong\u003e4 springs\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eEnder \/ CR-10 — \u003cstrong\u003e4 springs\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBuy the count your build needs, plus a spare. Available in 1, 3, 5, 25, and 50 packs.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOuter diameter: \u003cstrong\u003e8 mm\u003c\/strong\u003e · Inner diameter: \u003cstrong\u003e4 mm\u003c\/strong\u003e (M4 clearance) · Free length: \u003cstrong\u003e20 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eType: light-load compression die spring, ground flat ends\u003c\/li\u003e\n\u003cli\u003eMaterial: heat-resistant spring steel · Finish: \u003cstrong\u003eblack\u003c\/strong\u003e (custom)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dfh.fm","offers":[{"title":"1","offer_id":48294407078110,"sku":"7101072518","price":1.25,"currency_code":"USD","in_stock":true},{"title":"3","offer_id":48294407110878,"sku":"7101072518-3","price":2.95,"currency_code":"USD","in_stock":true},{"title":"5","offer_id":48294407143646,"sku":"7101072518-5","price":3.95,"currency_code":"USD","in_stock":true},{"title":"25","offer_id":48294407176414,"sku":"7101072518-25","price":15.0,"currency_code":"USD","in_stock":true},{"title":"50","offer_id":48294407209182,"sku":"7101072518-50","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/8x20_yellow_springs_but_black.jpg?v=1687606578"},{"product_id":"btt-manta-ez-1-0","title":"BTT Manta EZ 1.0","description":"\u003cp\u003eThe BIGTREETECH MANTA E3EZ V1.0 is a motherboard developed by the 3D printing team of Shenzhen Bigtree Technology Co. to help you to take your Ender 3 to the next level whether that means running Klipper or even Marlin with all of the latest features. This is our first motherboard that incorporates “Manta” technology (B2B connectors for the CB1 or CM4 modules) and “EZ” technology (the ability to use the latest EZ drivers). Simply plug in the CB1 core board and EZ drivers on the motherboard to upgrade your Ender 3 printer to run Klipper. Due to there being no need for an external raspberry pi the Manta series saves you messy cabling and results in a highly compact implementation.\u003c\/p\u003e\n\n\u003cp\u003eMANTA series motherboards support SPI and HDMI screens.\u003c\/p\u003e\n\n\u003cp\u003eThe Manta E3EZ is directly compatible with the Ender-3. Since we crammed so much into this board, we were unable to keep the size 100% compatible with other Ender machines and so minor, printable adapters are required. To check if your machine requires an adapter, see this link: \u003ca href=\"https:\/\/github.com\/bigtreetech\/Manta-E3EZ\"\u003ehttps:\/\/github.com\/bigtreetech\/Manta-E3EZ\u003c\/a\u003e\u003c\/p\u003e","brand":"BigTreeTech","offers":[{"title":"Board Only","offer_id":45213842604254,"sku":"4336234462","price":49.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/ez1.png?v=1699351356"},{"product_id":"mean-well-lrs-100-24","title":"Mean Well LRS-100-24","description":"\u003ch2\u003eMean Well LRS-100-24 — 100W 24V enclosed switcher\u003c\/h2\u003e\n\u003cp\u003eA genuine Mean Well LRS-100-24: 24V DC at 4.5A continuous, 108W peak, in the same fanless enclosed package the LRS series is known for. This is the small-wattage tier of the family — the same build and terminals as the LRS-350-24 most people put in a printer, just rated for a fraction of the current.\u003c\/p\u003e\n\n\u003ch3\u003eWhat it actually powers\u003c\/h3\u003e\n\u003cp\u003eAt 108W max, this is \u003cstrong\u003enot\u003c\/strong\u003e the supply to run a printer's heated bed. A Voron, RatRig, or a Klipper-converted Ender pulls most of its current through the bed heater, and on a 24V machine a 235–300mm bed alone wants 200–360W+. That's why printer resellers skip the LRS-100 and start their kits at the LRS-200\/350 — it simply can't source the bed amps. We're honest about that: this unit is undersized for a full 24V printer.\u003c\/p\u003e\n\u003cp\u003eWhere 108W of clean 24V is genuinely useful in a printer-adjacent build:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA dedicated rail for 24V \u003cstrong\u003eelectronics and motion\u003c\/strong\u003e — control board, steppers, hotend heater, and fans — on a machine whose bed is heated separately (AC mains bed, SSR + AC silicone heater, or its own larger PSU).\u003c\/li\u003e\n\u003cli\u003e24V \u003cstrong\u003eaccessory and lighting loads\u003c\/strong\u003e: chamber LEDs, exhaust\/nevermore fans, a small toolchanger dock, or a second-stage enclosure.\u003c\/li\u003e\n\u003cli\u003eBench and lab duty — 24V solenoids, small actuators, LED strip, fixturing — anywhere a tidy enclosed 24V brick beats a wall wart.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIf you're building a complete 24V printer and this is your only supply, size up to an LRS-200-24 or LRS-350-24 instead. This one is right when 24V at up to ~4A covers the job.\u003c\/p\u003e\n\n\u003ch3\u003eThe wiring and safety reality\u003c\/h3\u003e\n\u003cp\u003eThis is a bare-terminal mains supply. The input side is line voltage on exposed screw terminals — there is no plug, no fuse, and no enclosure beyond the PSU's own vented case. Installing it means committing to the same standards a printer's mains side demands:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eYou provide the mains wiring.\u003c\/strong\u003e Line (L), Neutral (N), and Earth (FG) land on the screw terminals. Earth must be connected — the metal case is bonded to it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eYou provide the fuse.\u003c\/strong\u003e Mean Well builds in over-load, over-voltage, and short-circuit protection on the DC output, but the AC input still needs an external fuse or breaker sized for the supply and an inlet you can isolate.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThe terminals must be guarded.\u003c\/strong\u003e In an open frame or printer base, the live input terminals need a cover or a terminal guard so nothing can contact them.\u003c\/li\u003e\n\u003cli\u003eIt's \u003cstrong\u003efanless\u003c\/strong\u003e, cooled by convection through the mesh case — give it airflow and don't bury it in a sealed pocket.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNone of this is exotic; it's standard control-cabinet practice. But if you want a sealed, plug-and-go brick, this isn't it — this is the open, serviceable, screw-terminal form factor that lets you wire it into a printer or cabinet exactly how you want.\u003c\/p\u003e\n\n\u003ch3\u003eWhy this form factor\u003c\/h3\u003e\n\u003cp\u003eThe LRS enclosed format is the workshop default for a reason: 30mm low profile so it tucks under a printer or along a DIN-equipped panel, a vented metal case that takes abuse, a trim pot to nudge the output, and full-range 85–264VAC input — so there's \u003cstrong\u003eno 115\/230V selector switch to get wrong\u003c\/strong\u003e (the larger LRS-150\/200\/350 units do have that switch; the LRS-100 auto-ranges). It's TUV\/UL-recognized to the current IEC 62368-1 safety standard.\u003c\/p\u003e\n\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput:\u003c\/strong\u003e 24V DC, 4.5A continuous (100W rated, 108W peak)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput:\u003c\/strong\u003e 85–264VAC full range, auto-ranging, 47–63Hz\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEfficiency:\u003c\/strong\u003e ~90%, \u0026lt;0.3W no-load\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCooling:\u003c\/strong\u003e fanless \/ free-air convection\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDimensions:\u003c\/strong\u003e 129 x 97 x 30mm (5.08 x 3.82 x 1.18 in)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperating temp:\u003c\/strong\u003e -30°C to +70°C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtections:\u003c\/strong\u003e over-voltage, overload, short-circuit; output trim pot\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety:\u003c\/strong\u003e UL62368-1, TUV EN62368-1, EN60335-1, EN61558\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eOn sale as a clearance — the lower-wattage tier moves slower than the bed-sized units, so it's priced to clear, not because there's anything wrong with it. It's the same genuine Mean Well part, just the right size for a smaller 24V job.\u003c\/p\u003e","brand":"MEAN WELL USA Inc.","offers":[{"title":"Default Title","offer_id":44779818647774,"sku":"9980652952","price":24.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/mean-well-lrs-100-24.jpg?v=1707757281"},{"product_id":"mean-well-lrs-100-5","title":"Mean Well LRS-100-5","description":"\u003ch2\u003eMean Well LRS-100-5 — 5V 18A (90W) enclosed switching supply\u003c\/h2\u003e\n\u003cp\u003eThis is the small, low-voltage member of Mean Well's \u003cstrong\u003eLRS enclosed metal-case family\u003c\/strong\u003e — the same fanless, screw-terminal switcher line as the LRS-350-24 that powers Voron beds, but configured for \u003cstrong\u003e5V at 18A\u003c\/strong\u003e instead of 24V. In a 3D-printer build this is the supply you reach for when you need a clean, dedicated 5V rail: a Raspberry Pi (or CB1\/CM4) running Klipper, an MCU\/control board's logic supply, LED strips, fans, or other 5V accessories. It is \u003cem\u003enot\u003c\/em\u003e a bed-heater supply — for the heated bed and 24V electronics on a Voron\/RatRig you want a 24V LRS unit. Use this alongside one.\u003c\/p\u003e\n\n\u003ch3\u003eThe real spec (read the part number carefully)\u003c\/h3\u003e\n\u003cp\u003eDespite the \"100\" in the name, the 5V model is rated \u003cstrong\u003e90W, not 100W\u003c\/strong\u003e: 5V x 18A = 90W. Mean Well derates the low-voltage members of the LRS-100 series, so you get \u003cstrong\u003e18A at 5V\u003c\/strong\u003e, not 20A. Plan your load budget around 90W \/ 18A. A Pi 4 under load plus a few 5V fans and an LED strip sits comfortably inside that; this supply has plenty of headroom for typical printer 5V duties.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput:\u003c\/strong\u003e 5V DC, 18A, 90W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInput:\u003c\/strong\u003e 85-264 VAC full range (no voltage-select jumper) or 120-370 VDC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEfficiency:\u003c\/strong\u003e ~86%\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCooling:\u003c\/strong\u003e free-air convection — fanless and silent, no fan to fail or add noise to the enclosure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDimensions:\u003c\/strong\u003e 129 x 97 x 30 mm — the 30 mm low-profile case, easy to tuck into an electronics bay\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtections:\u003c\/strong\u003e short circuit, overload, over-voltage\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutput trim:\u003c\/strong\u003e on-board SVR pot for fine 5V adjustment if you need to compensate for wire drop\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety\/EMC:\u003c\/strong\u003e UL\/CUL, TUV, CB, CE\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWiring and safety — this is a bare-terminal mains unit\u003c\/h3\u003e\n\u003cp\u003eBe clear-eyed about what you're buying: the LRS is an \u003cstrong\u003eopen-frame-style enclosed supply with exposed screw terminals\u003c\/strong\u003e, not a sealed wall-wart. The input side carries \u003cstrong\u003elive mains voltage\u003c\/strong\u003e on a screw terminal block. You are responsible for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMains wiring to the AC terminals\u003c\/strong\u003e (L, N, earth\/⏚). Earth\/ground \u003cem\u003emust\u003c\/em\u003e be connected to the metal case — this is non-negotiable for safety.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUpstream fusing and a means of disconnect.\u003c\/strong\u003e The LRS has internal short-circuit protection on its output, but it does \u003cem\u003enot\u003c\/em\u003e replace a properly rated mains fuse or breaker on the input. Fuse it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStrain relief and a terminal cover.\u003c\/strong\u003e A clear plastic terminal guard is included; fit it. Don't leave live screw terminals exposed inside a printer enclosure.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIf you're not comfortable terminating mains-voltage screw terminals and fusing an AC input, have someone who is do the install. This is standard practice for every LRS\/HDR-class supply — it's the trade-off for the compact, cheap, field-serviceable form factor.\u003c\/p\u003e\n\n\u003ch3\u003eWhy this form factor\u003c\/h3\u003e\n\u003cp\u003eThe enclosed LRS case is the workhorse choice for printer builds: a vented steel shell, convection cooling (no fan noise), screw terminals you can actually service, and a price that's hard to argue with. The slim 30 mm height makes it easy to mount flat in an electronics compartment. If you instead want a clean DIN-rail control-cabinet install, look at the HDR (ultra-slim DIN) or UHP (slim, PFC, kit-grade) families; for a fully encapsulated PCB-mount module there's the IRM series. For a 3D printer's 5V accessory rail, the LRS-100-5 is the straightforward, proven pick.\u003c\/p\u003e\n\n\u003ch3\u003eOn the price\u003c\/h3\u003e\n\u003cp\u003eThis unit is on clearance. For reference, hobby\/maker resellers list the LRS-100-5 around $27 (ProtoSupplies $26.95); component distributors like Digi-Key are lower at ~$18.60 in single quantity because they don't carry it as a niche printer part. Our clearance price sits between the two — a fair maker-channel price on the way out the door.\u003c\/p\u003e","brand":"MEAN WELL USA Inc.","offers":[{"title":"Default Title","offer_id":44779820679390,"sku":null,"price":12.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/LRS-100-5.jpg?v=1707757477"},{"product_id":"mean-well-hdr-60-5","title":"Mean Well HDR-60-5","description":"\u003ch2\u003eMean Well HDR-60-5 — 5V 6.5A (32.5W) DIN-rail PSU\u003c\/h2\u003e\n\u003cp\u003eAn ultra-slim DIN-rail supply that turns mains into a clean 5V\/6.5A rail. In a 3D-printer build this is the \u003cstrong\u003elow-voltage \/ logic\u003c\/strong\u003e supply, not the main motion supply. It runs a Raspberry Pi (Klipper host), an MCU board, a small display, LED strips, fans, or other 5V accessories that you want on a dedicated rail instead of stealing current from the toolboard or a USB brick.\u003c\/p\u003e\n\u003cp\u003eIt does \u003cstrong\u003enot\u003c\/strong\u003e power a 24V bed heater or 24V steppers — for that you want a 24V unit (the Voron standard). Pair this with your 24V main supply when you want the Pi and electronics on their own isolated, properly-fused source.\u003c\/p\u003e\n\n\u003ch3\u003eWhy the HDR form factor\u003c\/h3\u003e\n\u003cp\u003eHDR is Mean Well's ultra-slim \"step-shape\" DIN-rail line. It clips onto standard 35mm DIN rail (TS-35\/7.5 or TS-35\/15), so if your printer's electronics bay or control cabinet is built around a rail, this drops in clean next to your terminal blocks and breakers — no standoffs, no open-frame chassis to mount. The 52.5mm-wide (3SU) body is narrow, fanless, and silent. Compared to an open-frame LRS brick, you pay a bit more for the cabinet-grade packaging and the tidy rail mount.\u003c\/p\u003e\n\n\u003ch3\u003eThe honest wiring \/ safety reality\u003c\/h3\u003e\n\u003cp\u003eThis is a bare-terminal mains unit. Live AC (L\/N) lands on exposed screw terminals on one end; 5V DC comes off screw terminals on the other. That means:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eYou are responsible for the mains side.\u003c\/strong\u003e It needs an appropriately-rated inline fuse and proper mains wiring (correctly-gauged, strain-relieved, ferrules on stranded conductors). Nothing here is \"plug and play.\"\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClass II \/ no earth pin.\u003c\/strong\u003e The HDR series is double-insulated — there is no protective-earth (PE) terminal on the unit itself. Earth your chassis\/enclosure separately per your build's grounding scheme; do not assume the PSU bonds your frame.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMount it where terminals can't be touched.\u003c\/strong\u003e DIN-rail supplies live inside an enclosure for a reason. Keep the AC terminals covered\/inaccessible in the finished build.\u003c\/li\u003e\n\u003cli\u003eIf you're not comfortable terminating mains, stop and get someone who is. The DC side is harmless; the AC side will hurt you.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSpec at a glance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eOutput: 5V DC, 6.5A, 32.5W\u003c\/li\u003e\n\u003cli\u003eInput: 85-264VAC universal, 47-63Hz\u003c\/li\u003e\n\u003cli\u003eEfficiency ~85% (typ.), fanless free-air cooling\u003c\/li\u003e\n\u003cli\u003eOperating temp -30C to +70C\u003c\/li\u003e\n\u003cli\u003eOutput adjustable ~5.0-5.5V (up to ~+10%) via onboard trimmer\u003c\/li\u003e\n\u003cli\u003eShort-circuit \/ over-current (hiccup) \/ over-voltage protection\u003c\/li\u003e\n\u003cli\u003eMounts on TS-35 DIN rail; 52.5 x 90 x 54.5mm (W x H x D); ~0.19kg\u003c\/li\u003e\n\u003cli\u003e3-year Mean Well warranty\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eThis unit is on sale as part of a clearance — same genuine Mean Well part, lower price.\u003c\/p\u003e","brand":"MEAN WELL USA Inc.","offers":[{"title":"Default Title","offer_id":44779849908446,"sku":"7977873823","price":18.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/hdr-60-5.jpg?v=1707759483"},{"product_id":"zero-g-mercury-one-1-fasteners-kit","title":"Zero G Mercury One.1 Fasteners Kit","description":"\u003cp\u003eThe Mercury One.1 upgrade transforms your current Ender 5(Pro\/Plus) into a CoreXY system. This provides an improvement over the Cartesian system, which relies on V-rollers that may lack precision and demand considerable maintenance. Additionally, the CoreXY system is optimized for higher speeds, enhancing your 3D printing experience and quality.\u003c\/p\u003e\n\u003cp\u003eFastener kits come with 20% more fasteners, above BOM, and ship in reusable grid boxes. Kits available in stainless steel and black nickel coated stainless steel finishes. \u003c\/p\u003e\n\u003cp\u003eKit Includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e20S M3 Roll in spring loaded T-Nuts * 44\u003c\/li\u003e\n\u003cli\u003e20S M5 Roll in spring loaded T-Nuts * 25\u003c\/li\u003e\n\u003cli\u003eM5x50 ISO 4762 \/ DIN 912 * 10\u003c\/li\u003e\n\u003cli\u003eM5x20 ISO 4762 \/ DIN 912 * 10\u003c\/li\u003e\n\u003cli\u003eM5x12 ISO 4762 \/ DIN 912 * 10\u003c\/li\u003e\n\u003cli\u003eM5x8 ISO 4762 \/ DIN 912 * 10\u003c\/li\u003e\n\u003cli\u003eM3x35 ISO 4762 \/ DIN 912 * 15\u003c\/li\u003e\n\u003cli\u003eM3x30 ISO 4762 \/ DIN 912 * 10\u003c\/li\u003e\n\u003cli\u003eM3x25 ISO 4762 \/ DIN 912 * 10\u003c\/li\u003e\n\u003cli\u003eM3x20 ISO 4762 \/ DIN 912 * 20\u003c\/li\u003e\n\u003cli\u003eM3x16 ISO 4762 \/ DIN 912 * 12\u003c\/li\u003e\n\u003cli\u003eM3x12 ISO 4762 \/ DIN 912 * 10\u003c\/li\u003e\n\u003cli\u003eM3x8 ISO 4762 \/ DIN 912 * 80\u003c\/li\u003e\n\u003cli\u003eISO 4762 \/ DIN 912\u003c\/li\u003e\n\u003cli\u003eM3x5x4 Black Nickel Coated Brass Threaded Insert * 61 \u003c\/li\u003e\n\u003cli\u003eM3 Hex Nut * 15\u003c\/li\u003e\n\u003cli\u003eM3 Washer * 14\u003c\/li\u003e\n\u003cli\u003eM5 Washer * 40\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eMore information on the project may be found \u003ca href=\"https:\/\/docs.zerog.one\/\" title=\"Zero G Docs\" rel=\"noopener\" target=\"_blank\"\u003ehere\u003c\/a\u003e.\u003c\/p\u003e","brand":"dfh.fm","offers":[{"title":"Stainless Steel","offer_id":44823846355166,"sku":"4012333661","price":19.99,"currency_code":"USD","in_stock":true},{"title":"Black Nickel Coated Stainless Steel","offer_id":44823846387934,"sku":"1740735877","price":24.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/IMG_6429.jpg?v=1709019963"},{"product_id":"zero-g-mercury-one-1-linear-rails-kit","title":"Zero G Mercury One.1 Linear Rails Kit","description":"\u003cp\u003eThe Mercury One.1 upgrade transforms your current Ender 5(Pro\/Plus) into a CoreXY system. This provides an improvement over the Cartesian system, which relies on V-rollers that may lack precision and demand considerable maintenance. Additionally, the CoreXY system is optimized for higher speeds, enhancing your 3D printing experience and quality.\u003c\/p\u003e\n\u003cp\u003eRails kit includes 440c stainless steel MGN12H rails with a preload of Z1. Rails ship greased, but dry.\u003c\/p\u003e\n\u003cp\u003eSizes are 330mm, for 5 (Pro) and 450mm for Plus.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"dfh.fm","offers":[{"title":"Ender 5 (Pro)","offer_id":44830742085854,"sku":"9353240068","price":69.99,"currency_code":"USD","in_stock":true},{"title":"Ender 5 Plus","offer_id":44830742118622,"sku":"","price":89.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/IMG_6452.jpg?v=1709112726"},{"product_id":"zero-g-mercury-one-1-motion-kit","title":"Zero G Mercury One.1 Motion Kit","description":"\u003cp\u003eThe Mercury One.1 upgrade transforms your current Ender 5(Pro\/Plus) into a CoreXY system. This provides an improvement over the Cartesian system, which relies on V-rollers that may lack precision and demand considerable maintenance. Additionally, the CoreXY system is optimized for higher speeds, enhancing your 3D printing experience and quality.\u003c\/p\u003e\n\u003cp\u003eMotion kit ships with Gates 2GT belt (RF or EPDM), Runice idlers and pulleys (black or silver) and black anodized, high strength, lightweight aluminum 7075 pins.\u003c\/p\u003e\n\u003cp\u003eKit Includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eGates\u003c\/strong\u003e LL-2GT-6 RF|EPDM * 5m|6m\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRunice\u003c\/strong\u003e Pulley 20T 6mm Width * 2\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRunice\u003c\/strong\u003e Idler 20T 6mm Width * 2\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDFH\u003c\/strong\u003e 7075 Aluminum Pin M5x30mm * 10\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDFH\u003c\/strong\u003e F695-RS Bearings * 20\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eMore information on the project may be found \u003ca href=\"https:\/\/docs.zerog.one\/\" title=\"Zero G Docs\" rel=\"noopener\" target=\"_blank\"\u003ehere\u003c\/a\u003e.\u003c\/p\u003e","brand":"dfh.fm","offers":[{"title":"Silver \/ RF \/ 5m","offer_id":44908315508958,"sku":null,"price":39.99,"currency_code":"USD","in_stock":true},{"title":"Silver \/ RF \/ 6m","offer_id":44908327960798,"sku":"","price":42.99,"currency_code":"USD","in_stock":true},{"title":"Silver \/ EPDM \/ 5m","offer_id":44908315541726,"sku":null,"price":49.99,"currency_code":"USD","in_stock":true},{"title":"Silver \/ EPDM \/ 6m","offer_id":44908327993566,"sku":"","price":54.99,"currency_code":"USD","in_stock":false},{"title":"Black \/ RF \/ 5m","offer_id":44908328026334,"sku":"","price":42.99,"currency_code":"USD","in_stock":true},{"title":"Black \/ RF \/ 6m","offer_id":44908328059102,"sku":"","price":46.99,"currency_code":"USD","in_stock":true},{"title":"Black \/ EPDM \/ 5m","offer_id":44908328091870,"sku":"","price":54.99,"currency_code":"USD","in_stock":true},{"title":"Black \/ EPDM \/ 6m","offer_id":44908328124638,"sku":"","price":59.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/C41E69E2-F48B-4E39-B540-325DC85281C6_1_201_a.jpg?v=1710462600"}],"url":"https:\/\/formosissima.myshopify.com\/collections\/ender-mods.oembed?page=2","provider":"dfh.fm","version":"1.0","type":"link"}