{"title":"Hotends","description":"","products":[{"product_id":"extruder-collet-ecas04","title":"Extruder Collet ECAS04","description":"\u003cp\u003e\u003cstrong\u003eReplacement ECAS04 embedded Bowden collet for 4 mm OD PTFE\/FEP tube.\u003c\/strong\u003e Press-fit coupler for extruders, toolheads, and ERCF-style filament paths where the tube needs to lock directly into a printed or machined housing.\u003c\/p\u003e\n\u003ch3\u003eWhy use ECAS04?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eLow-profile embedded fitting: the body presses into the part instead of adding a tall threaded pneumatic fitting.\u003c\/li\u003e\n\u003cli\u003eBuilt for \u003cstrong\u003e4 mm OD Bowden\/PTFE-style tubing\u003c\/strong\u003e used around 1.75 mm filament paths.\u003c\/li\u003e\n\u003cli\u003eUseful as a replacement collet for worn extruder couplers or as a spare for printed mods that specify ECAS04.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eModel:\u003c\/strong\u003e ECAS04\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTube fit:\u003c\/strong\u003e 4 mm outside-diameter PTFE\/FEP\/Bowden tube\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting style:\u003c\/strong\u003e embedded push-fit \/ press-fit coupler for approximately 8 mm housing holes\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 1 collet assembly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVisible parts:\u003c\/strong\u003e black push-fit body with blue release cap\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWorks in extruders, toolheads, filament sensors, and ERCF-style filament routing parts that call for an ECAS04 embedded collet.\u003c\/li\u003e\n\u003cli\u003ePairs with \u003ca href=\"https:\/\/dfh.fm\/products\/transparent-fep-tube\"\u003eTransparent FEP Tube\u003c\/a\u003e and a \u003ca href=\"https:\/\/dfh.fm\/products\/collet-clip\"\u003eCollet Clip\u003c\/a\u003e where the build uses 4 mm OD tubing and a retained push-fit connector.\u003c\/li\u003e\n\u003cli\u003eAlso used by mods such as the \u003ca href=\"https:\/\/dfh.fm\/products\/cw2-with-ecas04-and-optional-sensor-kit\"\u003eCW2 With ECAS04 and Optional Sensor Kit\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNot a PC4-M10 or PC4-M6 threaded pneumatic fitting; use the \u003ca href=\"https:\/\/dfh.fm\/products\/pc4-01-pneumatic-fitting\"\u003ePC4-01 \/ PC4-M10 Press Fit Pneumatic Fitting\u003c\/a\u003e when your part calls for that style.\u003c\/li\u003e\n\u003cli\u003eNot a tube lock by itself; add a compatible collet clip if your build needs the release collar held up.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dfh.fm","offers":[{"title":"1","offer_id":39612701802665,"sku":"CHAO-00000080","price":0.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/IMG_8407_0.5x_0.5x.jpg?v=1624650859"},{"product_id":"thermistor-100k-ohm-ntc-3950","title":"Thermistor 100K ohm NTC 3950","description":"\u003cp\u003e\u003cstrong\u003e100K NTC 3950 thermistor for 3D-printer hotends and heated beds.\u003c\/strong\u003e A common RepRap-style temperature sensor with \u003cstrong\u003e100KΩ resistance at 25°C\u003c\/strong\u003e, \u003cstrong\u003eB25\/50 3950K\u003c\/strong\u003e, and a \u003cstrong\u003e1m lead\u003c\/strong\u003e for replacing or building a standard printer temperature input.\u003c\/p\u003e\n\u003ch3\u003eWhy use this thermistor\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFirmware-friendly spec:\u003c\/strong\u003e 100K NTC \/ B3950 is one of the standard thermistor profiles used across Marlin, Klipper, and RepRap-style printer builds.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGeneral hotend or bed sensing:\u003c\/strong\u003e use it where your controller and firmware expect a 100K B3950 NTC sensor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1m cable:\u003c\/strong\u003e enough reach for most toolhead and small heated-bed wiring paths without adding an immediate splice.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSensor type: \u003cstrong\u003eNTC thermistor\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eNominal resistance: \u003cstrong\u003e100KΩ at 25°C\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eB-value: \u003cstrong\u003e3950K\u003c\/strong\u003e (B25\/50 family)\u003c\/li\u003e\n\u003cli\u003eCable length: \u003cstrong\u003e1m\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eUse case: 3D-printer hotend, heated bed, chamber, or general temperature-sensor input where a 100K B3950 thermistor is specified\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWorks as a replacement sensor for printer builds configured for a \u003cstrong\u003e100K NTC 3950\u003c\/strong\u003e thermistor.\u003c\/li\u003e\n\u003cli\u003ePair it with a \u003ca href=\"https:\/\/dfh.fm\/products\/heater-cartridge-24v-40w\"\u003e24V 40W heater cartridge\u003c\/a\u003e when rebuilding a standard hotend heater block.\u003c\/li\u003e\n\u003cli\u003eFor higher-temperature hotends, compare against the \u003ca href=\"https:\/\/dfh.fm\/products\/high-temperature-thermistor-ht-ntc100k\"\u003eHT-NTC100K high-temperature thermistor\u003c\/a\u003e before choosing this standard sensor.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNot a PT100 or PT1000 RTD sensor; use firmware settings for \u003cstrong\u003e100K NTC B3950\u003c\/strong\u003e, not RTD settings.\u003c\/li\u003e\n\u003cli\u003eNot a cartridge-style thermistor unless your heater block accepts this probe style.\u003c\/li\u003e\n\u003cli\u003eDo not use it above the temperature limit of your specific sensor construction, wire insulation, or connector.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dfh.fm","offers":[{"title":"Default Title","offer_id":39656232026281,"sku":"CHAO-0000178","price":2.0,"currency_code":"USD","in_stock":true}]},{"product_id":"heater-cartridge-24v-40w","title":"Heater Cartridge 24V 40W","description":"\u003cp\u003e\u003cstrong\u003e24V 40W hotend heater cartridge with a 1m lead.\u003c\/strong\u003e A straightforward replacement heater for 24V 3D-printer hotends that use a cartridge-style heating element.\u003c\/p\u003e\n\u003ch3\u003eWhy this one\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e24V \/ 40W\u003c\/strong\u003e output matches the common heater rating used on many modern printer hotends.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1m cable\u003c\/strong\u003e gives enough reach for most toolhead wire runs without immediately needing an extension.\u003c\/li\u003e\n\u003cli\u003eGood spare to keep on hand when rebuilding a hotend, repairing a damaged lead, or refreshing an older toolhead.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eVoltage: \u003cstrong\u003e24V DC\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003ePower: \u003cstrong\u003e40W\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eLead length: \u003cstrong\u003e1m\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eForm: cartridge-style hotend heater\u003c\/li\u003e\n\u003cli\u003eStore SKU: \u003cstrong\u003eCHAO-00000100\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eUse only on \u003cstrong\u003e24V\u003c\/strong\u003e printer electronics configured for a 40W hotend heater.\u003c\/li\u003e\n\u003cli\u003ePair it with a temperature sensor such as the \u003ca href=\"https:\/\/dfh.fm\/products\/thermistor-100k-ohm-ntc-3950\"\u003e100K NTC 3950 thermistor\u003c\/a\u003e for a full hotend refresh.\u003c\/li\u003e\n\u003cli\u003eNeed a different heater? Compare the \u003ca href=\"https:\/\/dfh.fm\/products\/slim-heater-cartridge-24v-40w\"\u003eSlim Heater Cartridge 24V 40W\u003c\/a\u003e or the \u003ca href=\"https:\/\/dfh.fm\/products\/24v-50w-heater-cartridge-2m-length\"\u003e24V 50W Heater Cartridge - 2m Length\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNot a 12V heater. Do not install it on a 12V printer.\u003c\/li\u003e\n\u003cli\u003eNot a complete hotend kit; heater block, thermistor, connector, and fasteners are not included.\u003c\/li\u003e\n\u003cli\u003eCheck your hotend cartridge bore and wiring termination before installing.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dfh.fm","offers":[{"title":"Default Title","offer_id":39656347599017,"sku":"CHAO-00000100","price":3.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/IMG_8152_0.5x.png?v=1653557438"},{"product_id":"collet-clip","title":"Collet Clip","description":"\u003cp\u003e\u003cstrong\u003eLock 4 mm PTFE\/Bowden tubing in the push-fit coupler instead of letting the collet walk during retractions.\u003c\/strong\u003e This orange plastic collet clip snaps under the release collar on common 4 mm OD PTFE push-fit connectors used on 3D-printer extruders, hotends, and ERCF-style filament paths.\u003c\/p\u003e\n\u003ch3\u003eWhy use a collet clip?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHelps keep the PTFE tube seated by preventing the push-fit collar from being pressed down accidentally.\u003c\/li\u003e\n\u003cli\u003eReduces small back-and-forth tube movement at the connector during extrusion and retraction.\u003c\/li\u003e\n\u003cli\u003eCheap insurance for Bowden, hotend, toolhead, and multi-material filament paths where a loose tube causes jams or inconsistent feeding.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFor \u003cstrong\u003e4 mm OD PTFE\/Bowden tube\u003c\/strong\u003e push-fit collets and couplers.\u003c\/li\u003e\n\u003cli\u003eWorks with many embedded Bowden couplings and PC4-style 3D-printer tube fittings where the clip can sit under the plastic release collar.\u003c\/li\u003e\n\u003cli\u003eUseful on \u003ca href=\"https:\/\/dfh.fm\/products\/enraged-rabbit-carrot-feeder\"\u003eERCF\u003c\/a\u003e \/ Voron filament paths, extruders, and hotends that use 4 mm OD tube.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePairs with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/dfh.fm\/products\/transparent-fep-tube\"\u003eTransparent FEP Tube\u003c\/a\u003e for low-friction filament runs.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/dfh.fm\/products\/pc4-01-pneumatic-fitting\"\u003ePC4-01 \/ PC4-M10 Press Fit Pneumatic Fitting\u003c\/a\u003e where a clip fits under the release collar.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/dfh.fm\/products\/extruder-collet-ecas04\"\u003eExtruder Collet ECAS04\u003c\/a\u003e for 4 mm tube retention in compact extruder assemblies.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat you get\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne\u003c\/strong\u003e orange collet-retaining clip.\u003c\/li\u003e\n\u003cli\u003eTube, collet, and pneumatic fitting are not included.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis is not a tube connector by itself; it only locks a compatible connector's collet.\u003c\/li\u003e\n\u003cli\u003eCheck the gap under your fitting's release collar before ordering. Some nonstandard couplers use a different clip size.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dfh.fm","offers":[{"title":"Default Title","offer_id":40515900145833,"sku":"CHAO-02765459","price":0.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/IMG_8598_0.5x.jpg?v=1621827171"},{"product_id":"24v-50w-heater-cartridge-2m-length","title":"24v 50w Heater Cartridge - 2m Length","description":"\u003cp\u003e\u003cstrong\u003e24V 50W hotend heater cartridge with a 2m lead\u003c\/strong\u003e for 3D printer hotends that use the common cartridge-style heater format.\u003c\/p\u003e\n\u003ch3\u003eWhy use the 50W \/ 2m version\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e50W output\u003c\/strong\u003e gives faster heat-up and more headroom than a typical 40W cartridge, especially on higher-flow hotends.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24V wiring\u003c\/strong\u003e matches modern Voron, Klipper, Ender-style, and other 24V printer electronics.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2m lead length\u003c\/strong\u003e is useful for toolhead harnesses, umbilicals, and printers where a short heater lead will not comfortably reach the electronics bay.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 24V DC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower:\u003c\/strong\u003e 50W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLead length:\u003c\/strong\u003e 2m\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCartridge style:\u003c\/strong\u003e cylindrical hotend heater cartridge; verify your heater block accepts the standard 3D-printer cartridge size before installing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector:\u003c\/strong\u003e unterminated lead; fit your own connector or wire to the toolhead harness\/control board as appropriate.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment and pairing\u003c\/h3\u003e\n\u003cp\u003eUse this as a replacement or upgrade heater for compatible 24V hotends. Pair it with a verified temperature sensor such as the \u003ca href=\"https:\/\/dfh.fm\/products\/thermistor-100k-ohm-ntc-3950\"\u003e100K NTC 3950 thermistor\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/pt1000-temperature-sensor\"\u003ePT1000 temperature sensor\u003c\/a\u003e, or \u003ca href=\"https:\/\/dfh.fm\/products\/high-temperature-thermistor-ht-ntc100k\"\u003ehigh-temperature HT-NTC100K thermistor\u003c\/a\u003e depending on your firmware and hotend setup.\u003c\/p\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eConfirm your printer is \u003cstrong\u003e24V\u003c\/strong\u003e; do not install this on a 12V heater output.\u003c\/li\u003e\n\u003cli\u003eA 50W cartridge can overshoot if the printer was tuned for a lower-power heater. Run PID tuning after installation.\u003c\/li\u003e\n\u003cli\u003eThis is the heater only, not a thermistor, heater block, or full hotend assembly.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dfh.fm","offers":[{"title":"Default Title","offer_id":40873010626729,"sku":"3668088171","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/h.jpg?v=1626564453"},{"product_id":"phaetus-dragonfly-bmo","title":"Phaetus Dragonfly BMO","description":"\u003cp\u003e\u003cstrong\u003ePhaetus Dragonfly BMO is an all-metal, V6-interface hotend for 1.75 mm filament.\u003c\/strong\u003e It uses a copper-alloy thermal core, a conical bi-metal heatbreak, and a plated copper V6-style nozzle to make high-temperature materials practical without giving up clean filament control.\u003c\/p\u003e\n\u003ch3\u003eWhy this over a basic V6 hotend\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigher-temperature material range:\u003c\/strong\u003e the Dragonfly BMO is specified for operation up to \u003cstrong\u003e500°C\u003c\/strong\u003e when paired with the correct heater cartridge and sensor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBetter heat control:\u003c\/strong\u003e the conical heatbreak\/heatsink interface improves thermal isolation and helps reduce heat creep compared with conventional hotends.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eV6-style fit:\u003c\/strong\u003e BMO is the V6-interface Dragonfly model, intended for printers and toolheads built around a V6 hotend mount.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFilament path quality:\u003c\/strong\u003e the internal bore is specified at \u003cstrong\u003e≤ Ra0.3\u003c\/strong\u003e roughness for steadier filament flow.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eModel:\u003c\/strong\u003e Phaetus Dragonfly Hotend BMO, black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFilament:\u003c\/strong\u003e \u003cstrong\u003e1.75 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNozzle interface:\u003c\/strong\u003e V6-style \u003cstrong\u003eM6\u003c\/strong\u003e nozzle; supplied configuration is commonly listed with a \u003cstrong\u003e0.4 mm plated copper nozzle\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHotend size:\u003c\/strong\u003e \u003cstrong\u003e62.35 mm × 21.7 mm × 18 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterials:\u003c\/strong\u003e aluminum heatsink, copper-alloy heatbreak\/heatblock, titanium-alloy support screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer no.:\u003c\/strong\u003e \u003cstrong\u003eA189-01A-15-3\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment and use\u003c\/h3\u003e\n\u003cp\u003eUse the Dragonfly BMO where you need a V6-style all-metal hotend for Prusa MK3\/MK3S-style setups, Titan\/BMG-style extruder mounts, or Voron-style toolheads that are designed around a V6 interface. Pair it with a suitable heater cartridge, temperature sensor, and V6 nozzle for your material.\u003c\/p\u003e\n\u003cp\u003eFor spares and tuning, see our \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-dragonfly-sock\"\u003ePhaetus Dragonfly Sock\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-copper-plated-v6-style-1-75mm-nozzle\"\u003ePhaetus copper-plated V6 nozzles\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus hardened steel V6 nozzles\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/heater-cartridge-24v-40w\"\u003e24V 40W heater cartridge\u003c\/a\u003e, and \u003ca href=\"https:\/\/dfh.fm\/products\/thermistor-cartridge\"\u003eRunice high-temperature thermistor cartridge\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eMaterial guide\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eGood fit for PLA, PETG, ABS, ASA, TPU, Nylon, PC, PEI, PEEK, and other high-temperature thermoplastics when the rest of the toolhead is built for those temperatures.\u003c\/li\u003e\n\u003cli\u003eFor carbon-fiber, glass-fiber, glow, metal-fill, wood-fill, and other abrasive filaments, use a hardened or otherwise abrasion-resistant V6 nozzle instead of a standard plated copper nozzle.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eNot a Creality-style BMS\u003c\/h3\u003e\n\u003cp\u003eThis is the \u003cstrong\u003eBMO\u003c\/strong\u003e version for V6-style mounting. If your printer expects the Creality-style Dragonfly BMS heatsink geometry, this is not the drop-in version.\u003c\/p\u003e","brand":"Phaetus","offers":[{"title":"Black","offer_id":41053958865065,"sku":"2405842394","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/BMO_1.jpg?v=1696739009"},{"product_id":"phaetus-brass-v6-style-1-75mm-nozzle","title":"Phaetus Brass V6 Style 1.75mm Nozzle","description":"\u003cp\u003e\u003cstrong\u003eGenuine Phaetus brass PS\/V6 nozzle for everyday 1.75 mm printing.\u003c\/strong\u003e This is the standard M6-thread, V6\/RepRap-style brass nozzle for clean PLA, PETG, ABS, ASA, TPU, Nylon, HIPS, PVA, PC and other non-abrasive filament work.\u003c\/p\u003e\n\n\u003ch3\u003eWhy use brass here?\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFast, stable heat transfer:\u003c\/strong\u003e Phaetus rates the brass nozzle at \u003cstrong\u003e105 W\/m·K\u003c\/strong\u003e thermal conductivity, which keeps normal filament profiles predictable.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eClean extrusion path:\u003c\/strong\u003e Phaetus specifies inner-hole roughness of \u003cstrong\u003e≤Ra0.4 µm\u003c\/strong\u003e, \u003cstrong\u003e±0.01 mm\u003c\/strong\u003e orifice tolerance, and \u003cstrong\u003e≤0.02 mm\u003c\/strong\u003e concentricity.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRight tool for normal plastics:\u003c\/strong\u003e use brass for standard filaments; step up to a \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus hardened steel V6 nozzle\u003c\/a\u003e or \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-v2-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus DLC hardened steel V6 nozzle\u003c\/a\u003e for carbon, glass, glow, metal, wood, or other abrasive-filled materials.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGood inexpensive refresh:\u003c\/strong\u003e a worn nozzle can cause stringing, poor first layers, inconsistent extrusion, and oversized lines. Replacing it is cheaper than chasing slicer settings.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Phaetus\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eModel \/ family:\u003c\/strong\u003e PS (V6), M6 RepRap\/V6 style\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFilament diameter:\u003c\/strong\u003e 1.75 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNozzle sizes:\u003c\/strong\u003e 0.4, 0.5, 0.6, and 0.8 mm variants\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e brass, Mohs hardness \u003cstrong\u003e3\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMaximum printing temperature:\u003c\/strong\u003e \u003cstrong\u003e300 °C\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThermal conductivity:\u003c\/strong\u003e \u003cstrong\u003e105 W\/m·K\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eInner-hole roughness:\u003c\/strong\u003e \u003cstrong\u003e≤Ra0.4 µm\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOrifice tolerance:\u003c\/strong\u003e \u003cstrong\u003e±0.01 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConcentricity:\u003c\/strong\u003e \u003cstrong\u003e≤0.02 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eUse this with V6-style hotends and heater blocks that take a standard M6 RepRap\/V6 nozzle, including Phaetus Dragon\/Dragonfly-class hotends, E3D V6-style blocks, and compatible Mosquito\/Copperhead-style setups. It pairs cleanly with the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-dragonfly-bmo\"\u003ePhaetus Dragonfly BMO\u003c\/a\u003e and the \u003ca href=\"https:\/\/dfh.fm\/products\/v6-threaded-bi-metal-heatbreak\"\u003ePhaetus V6 threaded bi-metal heatbreak\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eWhich size should I pick?\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003e0.4 mm:\u003c\/strong\u003e default everyday nozzle size for balanced detail, speed, and profile compatibility.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e0.5 mm:\u003c\/strong\u003e a small flow bump without jumping all the way to chunky lines.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e0.6 mm:\u003c\/strong\u003e faster functional prints, stronger walls, and better throughput with common 0.24–0.32 mm layer heights.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e0.8 mm:\u003c\/strong\u003e large parts, draft work, vase mode, and maximum throughput when fine detail is not the priority.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eNot for abrasive-filled filament. Use hardened steel, DLC hardened steel, tungsten carbide, or similar wear-resistant nozzles for carbon\/glass\/glow\/wood\/metal-filled materials.\u003c\/li\u003e\n  \u003cli\u003eNot a Revo nozzle and not a Volcano\/Rapido UHF-length nozzle. Check your hotend thread and nozzle length before ordering.\u003c\/li\u003e\n  \u003cli\u003eInstall and hot-tighten according to your hotend manufacturer’s instructions to avoid leaks between the nozzle and heatbreak.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus","offers":[{"title":"0.4","offer_id":42123636900062,"sku":"2440308727","price":6.99,"currency_code":"USD","in_stock":false},{"title":"0.5","offer_id":43287147872478,"sku":"1475834587","price":6.99,"currency_code":"USD","in_stock":true},{"title":"0.6","offer_id":42123636932830,"sku":"2486046798","price":6.99,"currency_code":"USD","in_stock":true},{"title":"0.8","offer_id":42123636965598,"sku":"v3276106658","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/iu_d0273d6c-3fb7-4fac-a642-a9305222d9a1.png?v=1696736874"},{"product_id":"phaetus-copper-plated-v6-style-1-75mm-nozzle","title":"Phaetus Copper Plated V6 Style 1.75mm Nozzle","description":"\u003cp\u003e\u003cstrong\u003ePhaetus plated-copper V6-style nozzle for 1.75 mm filament.\u003c\/strong\u003e A high-conductivity M6 nozzle for V6-style hotends, built for stable extrusion and higher-temperature materials where ordinary brass runs out of thermal headroom.\u003c\/p\u003e\n\u003ch3\u003eWhy pick plated copper over brass?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e500°C maximum printing temperature\u003c\/strong\u003e for high-temperature polymers such as PEEK, PEKK, PEI, PSU and PPSU.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e330 W\/m·K thermal conductivity\u003c\/strong\u003e helps keep the nozzle tip evenly heated during fast or high-flow printing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNickel-plated copper alloy\u003c\/strong\u003e improves smoothness and reduces plastic sticking compared with bare brass.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRa \u0026lt; 0.4 internal roughness\u003c\/strong\u003e helps keep extrusion consistent through the filament path.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eBrand: \u003cstrong\u003ePhaetus\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eStyle: \u003cstrong\u003eV6 \/ PS M6\u003c\/strong\u003e nozzle\u003c\/li\u003e\n\u003cli\u003eFilament diameter: \u003cstrong\u003e1.75 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eThread: \u003cstrong\u003eM6\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaterial: \u003cstrong\u003eplated copper alloy\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eHardness: \u003cstrong\u003eMohs 6\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eThermal conductivity: \u003cstrong\u003e330 W\/m·K\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eExpansion coefficient: \u003cstrong\u003e16.7 μm\/m·°C\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum printing temperature: \u003cstrong\u003e500°C\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eUse this anywhere you need a standard V6-style 1.75 mm M6 nozzle, including compatible Phaetus hotends such as the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-dragonfly-bmo\"\u003ePhaetus Dragonfly BMO\u003c\/a\u003e. If you are refreshing a V6 toolhead, pair it with a clean \u003ca href=\"https:\/\/dfh.fm\/products\/v6-threaded-bi-metal-heatbreak\"\u003ePhaetus V6 threaded bi-metal heatbreak\u003c\/a\u003e while the hotend is apart.\u003c\/p\u003e\n\u003ch3\u003eHow to choose\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.4 mm\u003c\/strong\u003e is the everyday baseline for PLA, PETG, ABS and ASA.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.6 mm\u003c\/strong\u003e and \u003cstrong\u003e0.8 mm\u003c\/strong\u003e trade fine detail for higher flow, stronger walls and faster functional prints.\u003c\/li\u003e\n\u003cli\u003eFor ordinary non-abrasive work where cost matters more than temperature headroom, see the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-brass-v6-style-1-75mm-nozzle\"\u003ePhaetus brass V6-style nozzle\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003eFor carbon fiber, glass fiber, glow or other abrasive blends, use a hardened option like the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-v2-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus DLC hardened steel V6-style nozzle\u003c\/a\u003e instead.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cp\u003eThis is not a Volcano-length nozzle and it is not a hardened abrasive-filament nozzle. It is the standard V6 \/ PS M6 plated-copper nozzle for 1.75 mm filament.\u003c\/p\u003e\n\u003cblockquote\u003e“Good nozzles — these are my daily drivers… Copper plated means it’s got great conductivity.”\u003c\/blockquote\u003e","brand":"Phaetus","offers":[{"title":"0.4","offer_id":42123641553118,"sku":"7394235247","price":12.99,"currency_code":"USD","in_stock":true},{"title":"0.05","offer_id":44747815616734,"sku":"4665637331","price":12.99,"currency_code":"USD","in_stock":true},{"title":"0.6","offer_id":42123641585886,"sku":"6184044223","price":12.99,"currency_code":"USD","in_stock":true},{"title":"0.8","offer_id":42123641618654,"sku":"4938091458","price":12.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/iu_ec1b12c4-9cca-4df6-a76a-3d484ce870ca.png?v=1696737014"},{"product_id":"phaetus-hardened-steel-v6-style-1-75mm-nozzle","title":"Phaetus Hardened Steel V6 Style 1.75mm Nozzle","description":"\u003cp\u003e\u003cstrong\u003ePhaetus PS (V6) hardened steel nozzle for 1.75 mm filament.\u003c\/strong\u003e A drop-in M6\/V6-style wear-resistant nozzle for abrasive composites like carbon-fiber, glass-fiber, wood-fill, glow, and other filled materials.\u003c\/p\u003e\n\u003ch3\u003eWhy use hardened steel here?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardened tool steel\u003c\/strong\u003e resists bore wear from abrasive filaments that quickly enlarge a brass nozzle.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e450℃ maximum printing temperature\u003c\/strong\u003e covers common engineering and composite filament use cases.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e≤Ra0.4 μm inner-hole roughness\u003c\/strong\u003e and \u003cstrong\u003e≤0.02 mm concentricity\u003c\/strong\u003e help keep extrusion consistent.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eBrand \/ series: \u003cstrong\u003ePhaetus PS (V6) Hardened Steel Nozzle\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eFilament diameter: \u003cstrong\u003e1.75 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eNozzle thread\/style: \u003cstrong\u003eM6 V6-style \/ PS\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eAvailable orifice sizes here: \u003cstrong\u003e0.4, 0.5, 0.6, 0.8, and 1.0 mm\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eHardness: \u003cstrong\u003eover HRC60\u003c\/strong\u003e \/ Mohs \u003cstrong\u003e7.8\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum printing temperature: \u003cstrong\u003e450℃\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eThermal conductivity: \u003cstrong\u003e22 W\/m·K\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eManufacturer family \/ adaptation model: \u003cstrong\u003e1100-PS-HS\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment and use\u003c\/h3\u003e\n\u003cp\u003eUse this on hotends that take standard V6-style M6 nozzles, including Phaetus Dragon\/Dragonfly-style V6 setups and other compatible E3D V6 ecosystem heater blocks. It is the practical upgrade when printing abrasive materials like PET-CF, PA-CF, ABS-GF, ASA-GF, wood-fill, glow, or metal-filled filament.\u003c\/p\u003e\n\u003ch3\u003eChoosing the size\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.4 mm\u003c\/strong\u003e: general-purpose replacement when you need abrasion resistance without changing your normal profile much.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.5–0.6 mm\u003c\/strong\u003e: better flow and stronger parts for filled engineering materials.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.8–1.0 mm\u003c\/strong\u003e: faster, heavier extrusion for large functional parts and abrasive filaments that dislike tiny bores.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eRelated options\u003c\/h3\u003e\n\u003cp\u003eFor non-abrasive everyday filament, use the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-brass-v6-style-1-75mm-nozzle\"\u003ePhaetus Brass V6 Style 1.75 mm Nozzle\u003c\/a\u003e. For higher thermal conductivity, step to the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-copper-plated-v6-style-1-75mm-nozzle\"\u003ePhaetus Copper Plated V6 Style 1.75 mm Nozzle\u003c\/a\u003e. For a longer-life coated wear nozzle, compare the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-v2-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus DLC Hardened Steel V6 Style 1.75 mm Nozzle\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHardened steel conducts heat less efficiently than brass, so abrasive-material profiles may need a small temperature or flow tune.\u003c\/li\u003e\n\u003cli\u003eThis is \u003cstrong\u003enot\u003c\/strong\u003e a Volcano\/PH-length nozzle and is \u003cstrong\u003enot\u003c\/strong\u003e for Revo hotends.\u003c\/li\u003e\n\u003cli\u003eMatch the orifice size to your slicer profile before printing.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus","offers":[{"title":"0.4","offer_id":42123658559710,"sku":"4102866795","price":12.99,"currency_code":"USD","in_stock":true},{"title":"0.5","offer_id":44129365164254,"sku":"1781991749","price":12.99,"currency_code":"USD","in_stock":true},{"title":"0.6","offer_id":42123658592478,"sku":"4591652232","price":12.99,"currency_code":"USD","in_stock":true},{"title":"0.8","offer_id":42123658625246,"sku":"8760075792","price":12.99,"currency_code":"USD","in_stock":true},{"title":"1","offer_id":44747815583966,"sku":"6955789013","price":12.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/iu_b6826796-fcdc-4056-93cc-6b232f43e0da.png?v=1696739341"},{"product_id":"phaetus-v2-hardened-steel-v6-style-1-75mm-nozzle","title":"Phaetus DLC Hardened Steel V6 Style 1.75mm Nozzle","description":"\u003cp\u003e\u003cmeta charset=\"UTF-8\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eIn 3D printing filaments, composite consumables containing abrasive additives such as carbon fiber, steel, wood, boron carbide, tungsten and phosphorescent pigments are often very hard.The use of ordinary nozzle printing, will soon wear holes and inner diameter, destroying the original performance of the nozzle.\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eAnd Mohs type hardness of the hardened steel nozzle is 7.8, the highest printing temperature is 450℃, with high wear resistance, high temperature resistance. The hardened steel nozzle is the user's first choice for printing high strength filaments!\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cmeta charset=\"UTF-8\"\u003e\u003cspan\u003eHardness over HRC60 makes an minimum wear at the hole size after a long time printing with abrasive materials;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eTemperature resistance up to 450℃, easily handling with special engineering plastics such as PEEK;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eSpecial processing technology and post-treatment make the nozzle without burr at the edge of tip and without debris in the hole;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eInner hole roughness lower than Ra0.4; Higher smoothness and less adhesion;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eMin. diameter of hole 0.1mm\/±0.01mm in experimental level application, making sure high accuracy printing;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eHigh quality imported die steel material ensures the stability of performance.\u003c\/span\u003e\u003c\/p\u003e","brand":"Phaetus","offers":[{"title":"0.4","offer_id":42123681136862,"sku":"1267663720","price":29.99,"currency_code":"USD","in_stock":true},{"title":"0.5","offer_id":44130219196638,"sku":"3457709875","price":29.99,"currency_code":"USD","in_stock":true},{"title":"0.6","offer_id":42123681169630,"sku":"4555684610","price":26.99,"currency_code":"USD","in_stock":true},{"title":"0.8","offer_id":42123681202398,"sku":"5006088094","price":26.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/iu_84f73636-cf51-4cf0-b84a-a6b8e7c3046b.png?v=1696737652"},{"product_id":"e3d-revo-micro-24v","title":"E3D REVO MICRO 24V","description":"\u003cmeta charset=\"UTF-8\"\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cb data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003eReady for Revo.\u003c\/span\u003e\u003c\/b\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003e Change nozzles at room temperature using just your fingers. No complex tools, no hot tightening. Revo Nozzles are a factory sealed nozzle and heatbreak in one, so they’re easy to fit and can’t leak material when in use.\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\" data-ccp-props='{\"201341983\":0,\"335559739\":160,\"335559740\":259}'\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cb data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003eNew hotness.\u003c\/span\u003e\u003c\/b\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003e A Revo HeaterCore heats up in seconds. It’s much safer too – \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003eunlike other solutions on the market, a \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003epositive temperature coefficient (PTC) means the Revo HeaterCore can \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003enot\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003e melt at extreme temperatures: \u003c\/span\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003epower reduces as it gets hotter, so hazards are reduced in the event of a thermal runaway.\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\" data-ccp-props='{\"201341983\":0,\"335559739\":160,\"335559740\":259}'\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cb data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003eRuns cool, looks cool. \u003c\/span\u003e\u003c\/b\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003eWith an anodised black heatsink, not only does Revo Micro run cool – it looks cool, too.\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\" data-ccp-props='{\"201341983\":0,\"335559739\":160,\"335559740\":259}'\u003e \u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cb data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003eFlexible to any setup.\u003c\/span\u003e\u003c\/b\u003e\u003cspan data-mce-fragment=\"1\" data-contrast=\"auto\"\u003e Revo Micro plays nice with Bowden and direct drive setups, but its lightweight construction makes it an ideal choice for Bowden setups.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\" style=\"text-decoration: underline;\" data-mce-style=\"text-decoration: underline;\"\u003e\u003c\/span\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePlease note: \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e- This kit does not include any 3D printed mounts\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e- The Revo Micro fan \u003cstrong data-mce-fragment=\"1\"\u003emust\u003c\/strong\u003e be connected using the 5V regulator unless connecting directly to a 5V pin\u003c\/p\u003e","brand":"E3D","offers":[{"title":"Hotend Only","offer_id":42588509569246,"sku":"5075104399","price":49.99,"currency_code":"USD","in_stock":true},{"title":"Fully Loaded Kit (3 nozzles)","offer_id":42588509602014,"sku":"2049583984","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/47FD79B0-A55E-432D-9584-DF0D163AD456.png?v=1647743644"},{"product_id":"high-temperature-heater-cartridge","title":"50w High Temperature Heater Cartridge","description":"\u003ch4\u003eRunice heater cartrige.\u003c\/h4\u003e\n\u003cp\u003eReinforced fiberglass outer layer, embedded into the heating element, unlike lesser quality heaters which break away the sleeve from the heater after some amount of use.\u003c\/p\u003e\n\u003cp\u003eOne meter long. Ends terminated into ferrules.\u003c\/p\u003e","brand":"Phaetus","offers":[{"title":"Default Title","offer_id":42857902866654,"sku":"1419713996","price":7.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/IMG_1811.png?v=1653335547"},{"product_id":"hardened-steel-nozzle-by-runice","title":"Hardened Steel Nozzle by Runice","description":"\u003cmeta charset=\"UTF-8\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003eNozzle Diameter: 0.40mm, 0.60mm (+\/-0.006mm Tolerance)\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eFilament Size:1.75mm\u003c\/span\u003e\u003c\/div\u003e\n\u003cbr data-mce-fragment=\"1\"\u003e\n\u003cdiv data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eProduct Features:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Wear-resistance, High temperature performance\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Material Properties:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Hardness(Mohs):7.8\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Maximum Printing Temperature:450℃\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Thermal Conductivity:22 W\/m.k\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Expansion Coefficient:8.0μm\/m·℃\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Roughness: \u0026lt;=0.4Ra for inner hole.\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Suitable Materials:\u003c\/span\u003e\u003c\/div\u003e\n\u003cdiv style=\"padding-left: 30px;\" data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e Suitable for 3D printing composites with abrasive additives such as Carbon Fibre, Steel, Wood, Boron Carbide, Tungsten and Phosphorescent pigment as well as conventional materials.\u003c\/span\u003e\u003c\/div\u003e\n\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e","brand":"Runice","offers":[{"title":"0.5mm","offer_id":43269961908446,"sku":"5783692908","price":13.5,"currency_code":"USD","in_stock":false},{"title":"0.8mm","offer_id":43386721861854,"sku":"5002771599","price":13.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/V6HardenedSteel_e01d187b-df9b-41f7-85c4-9cadba182988.jpg?v=1660518691"},{"product_id":"nozzles-for-phaetus-dropeffect-xg-hotend","title":"Nozzles for Phaetus\/DropEffect XG hotend","description":"\u003cp\u003e\u003cstrong\u003eReplacement M4 nozzles for the Phaetus\/DropEffect XG hotend\u003c\/strong\u003e in 1.75 mm filament sizes. Choose brass for everyday materials, hardened steel for abrasive blends, or plated copper when you want better heat transfer and a cleaner exterior surface.\u003c\/p\u003e\n\u003ch3\u003eWhy this over a standard V6 nozzle\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThe DropEffect XG uses an \u003cstrong\u003eM4 threaded nozzle\u003c\/strong\u003e; standard V6\/M6 nozzles are not the right fit.\u003c\/li\u003e\n\u003cli\u003eAvailable here in the common XG sizes: \u003cstrong\u003e0.4 mm\u003c\/strong\u003e, \u003cstrong\u003e0.6 mm\u003c\/strong\u003e, and \u003cstrong\u003e0.8 mm\u003c\/strong\u003e for \u003cstrong\u003e1.75 mm\u003c\/strong\u003e filament.\u003c\/li\u003e\n\u003cli\u003eMaterial choices match the job: brass for PLA\/PETG\/ABS\/ASA\/TPU, hardened steel for carbon- or glass-filled abrasive filament, plated copper for higher thermal response and reduced plastic buildup versus bare brass.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand \/ ecosystem:\u003c\/strong\u003e Phaetus \/ DropEffect XG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread:\u003c\/strong\u003e M4\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFilament:\u003c\/strong\u003e 1.75 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiameters:\u003c\/strong\u003e 0.4 mm, 0.6 mm, 0.8 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterials:\u003c\/strong\u003e brass, hardened steel, plated copper\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse:\u003c\/strong\u003e replacement nozzle for DropEffect XG hotend installations\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to pick\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrass:\u003c\/strong\u003e best default for non-abrasive filament and normal print temperatures.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardened steel:\u003c\/strong\u003e use for PA-CF, PET-CF, glow, glass-filled, and other abrasive blends.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlated copper:\u003c\/strong\u003e use when you want stronger heat transfer than hardened steel and an easier-to-clean plated surface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.4 mm:\u003c\/strong\u003e detail\/default; \u003cstrong\u003e0.6 mm:\u003c\/strong\u003e faster everyday printing; \u003cstrong\u003e0.8 mm:\u003c\/strong\u003e coarse, high-throughput prints.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment and related parts\u003c\/h3\u003e\n\u003cp\u003eThese nozzles are for the Phaetus\/DropEffect XG hotend ecosystem. If you are refreshing the whole hotend, the live companion part in the shop is the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-dropeffect-high-temperature-m4-threaded-thermistor\"\u003ePhaetus\/DropEffect high-temperature M4 threaded thermistor\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNot a V6\/M6 nozzle. Do not buy this for Dragon, Dragonfly, Rapido, or other standard V6-style hotends unless your setup specifically uses the DropEffect XG M4 nozzle format.\u003c\/li\u003e\n\u003cli\u003eMatch nozzle material to filament: brass wears quickly with abrasive filled filaments.\u003c\/li\u003e\n\u003cli\u003eInstall hot and torque gently according to your hotend service routine; small M4 nozzles are easier to over-tighten than larger V6-style nozzles.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus","offers":[{"title":"XG M4 Threaded Brass Nozzle 0.4\/1.75mm","offer_id":43380588609758,"sku":"8320589597","price":7.99,"currency_code":"USD","in_stock":false},{"title":"XG M4 Threaded Brass Nozzle 0.6\/1.75mm","offer_id":43380588642526,"sku":"1931609937","price":7.99,"currency_code":"USD","in_stock":false},{"title":"XG M4 Threaded Brass Nozzle 0.8\/1.75mm","offer_id":43380588675294,"sku":"3191122147","price":7.99,"currency_code":"USD","in_stock":false},{"title":"XG M4 Threaded Hardened Steel Nozzle 0.4\/1.75mm","offer_id":43380588708062,"sku":"9528272413","price":7.99,"currency_code":"USD","in_stock":false},{"title":"XG M4 Threaded Hardened Steel Nozzle 0.6\/1.75mm","offer_id":43380588740830,"sku":"2838444954","price":7.99,"currency_code":"USD","in_stock":false},{"title":"XG M4 Threaded Hardened Steel Nozzle 0.8\/1.75mm","offer_id":43380588773598,"sku":"9641778176","price":7.99,"currency_code":"USD","in_stock":true},{"title":"XG M4 Threaded Plated Copper Nozzle 0.4\/1.75mm","offer_id":43380588806366,"sku":"9838094817","price":7.99,"currency_code":"USD","in_stock":true},{"title":"XG M4 Threaded Plated CopperNozzle 0.6\/1.75mm","offer_id":43380588839134,"sku":"9738292614","price":7.99,"currency_code":"USD","in_stock":true},{"title":"XG M4 Threaded Plated Copper Nozzle 0.8\/1.75mm","offer_id":43380588871902,"sku":"9664953204","price":7.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/ScreenShot2022-09-09at1.12.29PM.png?v=1696798837"},{"product_id":"60w-high-temperature-heater-cartridge","title":"60w High Temperature Heater Cartridge","description":"\u003ch4\u003eRunice heater cartrige.\u003c\/h4\u003e\n\u003cp\u003eReinforced fiberglass outer layer, embedded into the heating element, unlike lesser quality heaters which break away the sleeve from the heater after some amount of use.\u003c\/p\u003e\n\u003cp\u003eOne meter long. Ends terminated into ferrules.\u003c\/p\u003e","brand":"Phaetus","offers":[{"title":"Default Title","offer_id":43499839422686,"sku":"1401313540","price":7.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/IMG_1811_2d2b402d-32bb-4e4f-9b64-01d298567f98.png?v=1665195908"},{"product_id":"70w-high-temperature-heater-cartridge","title":"70w High Temperature Heater Cartridge","description":"\u003ch4\u003eRunice heater cartrige.\u003c\/h4\u003e\n\u003cp\u003eReinforced fiberglass outer layer, embedded into the heating element, unlike lesser quality heaters which break away the sleeve from the heater after some amount of use.\u003c\/p\u003e\n\u003cp\u003eOne meter long.\u003c\/p\u003e","brand":"Runice","offers":[{"title":"Default Title","offer_id":43499843453150,"sku":"3537993199","price":8.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/products\/IMG_3141.jpg?v=1665196069"},{"product_id":"phaetus-rapido-titanium-screw-m1-6-11","title":"Phaetus Rapido Titanium Screw M1.6*11","description":"\u003cp\u003e\u003cstrong\u003eGenuine Phaetus Rapido titanium replacement screw\u003c\/strong\u003e for Rapido hotend service work, sized \u003cstrong\u003eM1.6x11\u003c\/strong\u003e and sold individually.\u003c\/p\u003e\n\u003ch3\u003eWhy this over a generic screw\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTitanium hardware\u003c\/strong\u003e keeps heat transfer lower than ordinary steel in hotend assemblies.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCorrect small-format size:\u003c\/strong\u003e M1.6x11 for Rapido replacement use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBagged Phaetus spare\u003c\/strong\u003e with Rapido labeling, not loose mixed-bin hardware.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eBrand: \u003cstrong\u003ePhaetus\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eProduct: \u003cstrong\u003eRapido Titanium Screw\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eSize: \u003cstrong\u003eM1.6x11\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaterial: \u003cstrong\u003etitanium\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eQuantity: \u003cstrong\u003e1 screw\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment and use\u003c\/h3\u003e\n\u003cp\u003eUse this when servicing a Phaetus Rapido-family hotend that needs the M1.6x11 titanium screw. It pairs with the live \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-rapido-2\"\u003ePhaetus Rapido 2\u003c\/a\u003e lineup and Rapido hotend spare parts.\u003c\/p\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis is \u003cstrong\u003eone replacement screw only\u003c\/strong\u003e, not a full hotend, heat block, sock, or screw kit.\u003c\/li\u003e\n\u003cli\u003eMatch the screw location and length on your hotend before installing; tiny hotend screws are easy to mix up.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cblockquote\u003e“Important to get titanium.”\u003c\/blockquote\u003e","brand":"Phaetus","offers":[{"title":"Default Title","offer_id":44106609950942,"sku":"9034674945","price":2.49,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/IMG_43342.png?v=1696708919"},{"product_id":"phaetus-rapido-2","title":"Phaetus Rapido 2","description":"\u003cp\u003e\u003cstrong\u003ePhaetus Rapido 2 is a compact, fast-heating hotend family for high-flow 1.75 mm printing.\u003c\/strong\u003e This black 24V listing covers HF and UHF builds, with standard Rapido Hotend 2 280 °C variants and Rapido Plus Hotend 2 350 °C PT1000 variants.\u003c\/p\u003e\n\u003ch3\u003eWhy choose Rapido 2?\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTitanium heatbreak\u003c\/strong\u003e for thermal isolation and less heat creep than the original stainless heatbreak design.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAluminum heatsink + plated-copper extended heatblock\u003c\/strong\u003e for a longer melt zone and fast temperature response.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHF and UHF options\u003c\/strong\u003e let you choose a shorter high-flow setup or the longer ultra-high-flow configuration when your toolhead clearance allows it.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRemovable temperature sensor\u003c\/strong\u003e makes service simpler: 104NT on the 280 °C Rapido Hotend 2, PT1000 on the 350 °C Rapido Plus Hotend 2.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eOne-handed nozzle-change design\u003c\/strong\u003e with titanium alloy support screws to keep the heater block rigid.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Phaetus\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFilament:\u003c\/strong\u003e 1.75 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 24V\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e black\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFlow options:\u003c\/strong\u003e HF \/ UHF\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eTemperature options:\u003c\/strong\u003e Rapido Hotend 2 280 °C with 104NT sensor; Rapido Plus Hotend 2 350 °C with PT1000 sensor\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eConstruction:\u003c\/strong\u003e aluminum heatsink, titanium heatbreak, plated-copper heatblock, titanium alloy support screws\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNozzle ecosystem:\u003c\/strong\u003e V6-style nozzle compatible; pair with \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-copper-plated-v6-style-1-75mm-nozzle\"\u003ePhaetus plated-copper V6 nozzles\u003c\/a\u003e or \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus hardened-steel V6 nozzles\u003c\/a\u003e for spares.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMachine fitment and use\u003c\/h3\u003e\n\u003cp\u003eRapido 2 is a strong fit for high-speed CoreXY builds and Voron-style toolheads where a Phaetus\/Rapido mount is supported. It is commonly chosen for Voron V2.4, Trident, Switchwire, custom Klipper printers, and other machines that need more melt capacity without moving to a full toolhead swap. Keep a matching spare sock on hand: \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-rapido-2-high-temp-silicone-sock-hf\"\u003eRapido 2 HF silicone sock\u003c\/a\u003e or \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-rapido-2-high-temp-silicone-sock-uhf\"\u003eRapido 2 UHF silicone sock\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eHow to choose\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHF:\u003c\/strong\u003e choose this for a compact high-flow hotend when you want the simplest fit and do not need the longest melt zone.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eUHF:\u003c\/strong\u003e choose this when you are chasing higher volumetric flow and your toolhead has room for the longer setup.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e280 °C \/ 104NT:\u003c\/strong\u003e choose standard Rapido Hotend 2 for common engineering plastics within its temperature range.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e350 °C \/ PT1000 Plus:\u003c\/strong\u003e choose Rapido Plus Hotend 2 for higher-temperature materials and PT1000 sensor support.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eThis is a hotend, not a complete toolhead or extruder kit.\u003c\/li\u003e\n  \u003cli\u003eConfirm your printed mount, fan duct, wiring length, and firmware sensor type before installing.\u003c\/li\u003e\n  \u003cli\u003eRun PID tuning after installation, then re-check retraction and pressure advance.\u003c\/li\u003e\n  \u003cli\u003eFor abrasive filaments, use a hardened or wear-resistant nozzle rather than the basic plated-copper nozzle.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus","offers":[{"title":"Black \/ Rapido Hotend 2 280° HF","offer_id":44243213746398,"sku":"4536149660","price":99.99,"currency_code":"USD","in_stock":true},{"title":"Black \/ Rapido Hotend 2 280° UHF","offer_id":44243221119198,"sku":"8162336967","price":109.99,"currency_code":"USD","in_stock":true},{"title":"Black \/ Rapido Plus Hotend 2 350° HF","offer_id":44243221151966,"sku":"7939321660","price":109.99,"currency_code":"USD","in_stock":false},{"title":"Black \/ Rapido Plus Hotend 2 350° UHF","offer_id":44243221184734,"sku":"2743054383","price":119.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/Screenshot2023-06-24at8.34.51AM.png?v=1696710903"},{"product_id":"phaetus-rapido-plus-hotend-2_280-uhf-magenta_limited","title":"Phaetus Rapido Hotend 2_280° UHF Magenta_Limited","description":"\u003cp\u003e\u003cstrong\u003eLimited magenta Rapido Hotend 2 UHF for fast 1.75 mm printing.\u003c\/strong\u003e This is the 280°C \/ 104NT Rapido 2 UHF configuration: an aluminum heatsink, titanium heatbreak, plated-copper extended melt zone, planar ceramic heater, and UHF hardware for higher-flow printing.\u003c\/p\u003e\n\u003ch3\u003eWhy this over a standard HF hotend\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUHF melt path:\u003c\/strong\u003e the extended heatblock gives more melt length for high-speed extrusion.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eServiceable sensor:\u003c\/strong\u003e removable \u003cstrong\u003e104NT\u003c\/strong\u003e temperature sensor, matching the 280°C Rapido 2 configuration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeat control:\u003c\/strong\u003e titanium heatbreak and aluminum heatsink help keep heat where it belongs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLimited finish:\u003c\/strong\u003e magenta heatsink body instead of the usual blue or black Rapido 2 colorway.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eModel:\u003c\/strong\u003e Phaetus Rapido Hotend 2 UHF, magenta limited edition\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFilament:\u003c\/strong\u003e 1.75 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature sensor:\u003c\/strong\u003e 104NT removable sensor\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature rating:\u003c\/strong\u003e 280°C configuration\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHotend format:\u003c\/strong\u003e UHF \/ Ultra High Flow with extended melt zone\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNozzle ecosystem:\u003c\/strong\u003e V6-style M6 nozzles; pair with \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-copper-plated-v6-style-1-75mm-nozzle\"\u003ePhaetus copper-plated V6 nozzles\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus hardened steel V6 nozzles\u003c\/a\u003e, or \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-v2-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus DLC hardened steel V6 nozzles\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIntended use\u003c\/h3\u003e\n\u003cp\u003eUse this for high-speed FDM printers that need a compact, high-flow hotend for PLA, PETG, ABS\/ASA, and other 1.75 mm materials within the 280°C sensor configuration.\u003c\/p\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis is the \u003cstrong\u003e280°C \/ 104NT\u003c\/strong\u003e Rapido 2 version, not the 350°C PT1000 “Plus” configuration.\u003c\/li\u003e\n\u003cli\u003eFor abrasive filaments, use hardened or DLC hardened nozzles rather than brass.\u003c\/li\u003e\n\u003cli\u003eConfirm your firmware thermistor setting before heating the hotend.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus","offers":[{"title":"Default Title","offer_id":44316736848094,"sku":"7020489349","price":119.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/copy.jpg?v=1696709229"},{"product_id":"rapido-plus-hotend-2_350-uhf-magenta_limited","title":"Rapido Plus Hotend 2_350° UHF Magenta_Limited","description":"\u003cp\u003e\u003cstrong\u003ePhaetus Rapido Plus Hotend 2 UHF in limited magenta\u003c\/strong\u003e — a 24V, 350°C, PT1000-equipped all-metal hotend for high-speed and high-temperature 1.75mm printing.\u003c\/p\u003e\n\u003ch3\u003eWhy choose the Plus 2 UHF\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e350°C rating with PT1000 sensing\u003c\/strong\u003e for engineering materials that need more headroom than standard hotends.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRapido 2 titanium heatbreak\u003c\/strong\u003e and planar ceramic heater design improve heat control and reduce the clog\/deformation risk versus the earlier Rapido layout.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUHF configuration\u003c\/strong\u003e adds the extended melt-zone hardware buyers want for high-flow builds and Volcano-style nozzle setups.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne-handed nozzle-change design\u003c\/strong\u003e uses the rigid Rapido 2 block and titanium screw structure to make maintenance less annoying.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eModel:\u003c\/strong\u003e Phaetus Rapido Plus Hotend 2 UHF, limited magenta heatsink\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFilament:\u003c\/strong\u003e 1.75mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 24V\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaximum temperature:\u003c\/strong\u003e 350°C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature sensor:\u003c\/strong\u003e removable PT1000\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeater:\u003c\/strong\u003e planar ceramic heater\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNozzle ecosystem:\u003c\/strong\u003e V6-compatible by default; UHF setup is intended for extended\/Volcano-style high-flow use\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Phaetus\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment and use\u003c\/h3\u003e\n\u003cp\u003eUse this when you are building a high-flow toolhead for Voron-style, VzBot, RatRig, Annex, or other open-frame CoreXY printers that can actually use the extra melt capacity. Pair it with a \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-rapido-2-high-temp-silicone-sock-uhf\"\u003eRapido 2 UHF silicone sock\u003c\/a\u003e, spare \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-copper-plated-v6-style-1-75mm-nozzle\"\u003ePhaetus V6 copper-plated nozzles\u003c\/a\u003e, or a replacement \u003ca href=\"https:\/\/dfh.fm\/products\/pt1000-temperature-sensor\"\u003ePT1000 temperature sensor\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThis is the \u003cstrong\u003ePlus\u003c\/strong\u003e version with a PT1000 sensor and 350°C rating. Set the correct sensor type in firmware before heating it.\u003c\/li\u003e\n\u003cli\u003eRapido Plus Hotend and Rapido Plus Hotend 2 parts are not fully interchangeable even when the outside dimensions look similar.\u003c\/li\u003e\n\u003cli\u003eIt is magenta, not pink. That matters enough that a verified buyer said it out loud.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cblockquote\u003e“It's NOT pink. It's magenta.”\u003c\/blockquote\u003e","brand":"Phaetus","offers":[{"title":"Default Title","offer_id":44316736913630,"sku":"3670750007","price":129.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/Rapido2magenta2copy_e04c462c-0d35-4887-8686-7b2e09835117.jpg?v=1692439706"},{"product_id":"phaetus-rapido-2-leaf-spring-heater","title":"Phaetus Rapido 2 Leaf Spring - Heater","description":"\u003cp\u003e\u003cstrong\u003eOEM Phaetus heater leaf spring clip for Rapido 2.\u003c\/strong\u003e This is the small metal retainer spring used around the Rapido 2 heater block assembly; the package is marked \u003cstrong\u003e10.2 × 8.9 × 9 mm\u003c\/strong\u003e and 1 piece.\u003c\/p\u003e\n\u003ch3\u003eWhy this part matters\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eRestores the heater-side spring clip\/retainer instead of replacing the whole hotend.\u003c\/li\u003e\n  \u003cli\u003eUseful after a blob cleanup, teardown, or lost spring during hotend service.\u003c\/li\u003e\n  \u003cli\u003eOEM Phaetus spare part for Rapido 2-family heater hardware.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Phaetus\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart:\u003c\/strong\u003e Leaf Spring - Heater\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePackage size marking:\u003c\/strong\u003e 10.2 × 8.9 × 9 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 1 piece\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eUse:\u003c\/strong\u003e heater leaf spring \/ clip for Rapido v2 hotend hardware\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eFits Phaetus Rapido 2 hotends that use the M4 thermistor mount, including the non-plus Rapido 2 104NT model and the older Rapido 2 Plus PT1000 model.\u003c\/li\u003e\n  \u003cli\u003ePairs with the live \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-rapido-2\"\u003ePhaetus Rapido 2\u003c\/a\u003e listing and other Rapido 2 service parts.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eNot a heater cartridge\u003c\/h3\u003e\n\u003cp\u003eThis is the spring\/clip only. It is not a ceramic heater, thermistor, heat block, silicone sock, or complete hotend. If you are rebuilding the heater side, check the fit before ordering against your exact Rapido 2 version.\u003c\/p\u003e\n\u003cblockquote\u003e“It's a spring. It does what it does.”\u003c\/blockquote\u003e","brand":"Phaetus","offers":[{"title":"Default Title","offer_id":44519488487646,"sku":"2806874031","price":0.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/IMG_5643.png?v=1700040142"},{"product_id":"phaetus-dropeffect-next-g-extreme-gradient-hotend-104nt-version","title":"Phaetus DropEffect neXt G Extreme Gradient Hotend 104NT Version","description":"\u003cp\u003e\u003cstrong\u003eUltra-high-flow 104NT hotend for speed-focused 1.75 mm printers.\u003c\/strong\u003e The Phaetus \/ DropEffect neXt G 104NT uses a ceramic heating plate, V6 nozzle interface, and Dragon-style footprint for high-flow extrusion without forcing a full toolhead redesign.\u003c\/p\u003e\n\u003ch3\u003eWhy this over a standard hotend?\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eUp to 45 mm³\/s\u003c\/strong\u003e published flow target with the UHF groove adapter installed.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRigid kinematic coupling\u003c\/strong\u003e locks the heater block to reduce bending and help protect the heatbreak during nozzle changes or print strikes.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eV6-style nozzle compatibility\u003c\/strong\u003e keeps nozzle sourcing simple; pair it with our \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-copper-plated-v6-style-1-75mm-nozzle\"\u003ePhaetus copper-plated V6 nozzles\u003c\/a\u003e or \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-hardened-steel-v6-style-1-75mm-nozzle\"\u003ePhaetus hardened-steel V6 nozzles\u003c\/a\u003e.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDragon-style mounting footprint\u003c\/strong\u003e fits many Voron, Creality, and Dragon-compatible toolhead mounts; Prusa use is supported with the included groove-mount adapter.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eModel:\u003c\/strong\u003e DropEffect neXt G UHF hotend, red 104NT version\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFilament:\u003c\/strong\u003e 1.75 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eThermistor:\u003c\/strong\u003e 104NT\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNozzle temperature:\u003c\/strong\u003e 280°C+\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eMaximum flow target:\u003c\/strong\u003e up to 45 mm³\/s\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 52.4 × 23 × 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNet hotend weight:\u003c\/strong\u003e about 40 g\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eNozzle interface:\u003c\/strong\u003e V6-compatible; includes 0.4 mm and 0.6 mm plated copper nozzles\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHeatbreak:\u003c\/strong\u003e all-metal\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment and use\u003c\/h3\u003e\n\u003cp\u003eUse this for fast PLA, ABS, PETG, and similar high-flow builds where you want Dragon-style mount compatibility and V6 nozzle choice. It is a natural fit for Voron toolheads that support Dragon-style hotends, Prusa MK2\/MK3-style groove-mount conversions, and Creality setups with the right adapter.\u003c\/p\u003e\n\u003ch3\u003eGotchas\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eThis is the \u003cstrong\u003e104NT \/ 280°C+\u003c\/strong\u003e neXt G version, not the PT1000 Fiber version.\u003c\/li\u003e\n  \u003cli\u003eFor sustained abrasive CF\/GF work, use an appropriate hardened nozzle; the standard kit includes plated copper nozzles.\u003c\/li\u003e\n  \u003cli\u003eFirmware must be configured for the 104NT thermistor, followed by PID tuning and retraction \/ pressure-advance tuning after installation.\u003c\/li\u003e\n  \u003cli\u003eSome compact toolheads need adapter or wire-clearance checks because the heater and thermistor leads protrude from the assembly.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cblockquote\u003eVerified buyer note: “This hotend is really awesome… with a very short melt zone… same exact dimensions as the Phaetus Dragon without the UHF.”\u003c\/blockquote\u003e","brand":"Phaetus\/DropEffect","offers":[{"title":"Default Title","offer_id":44775733133534,"sku":"9482990061","price":89.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/Untitled-5.jpg?v=1707551660"},{"product_id":"wth-burner-by-kevinakasam","title":"WTH-Burner by kevinakasam","description":"\u003cp\u003eSay hello to WTH-Burner, an eighty percent scaled Stealthburner, designed by kevinakasam.\u003c\/p\u003e\n\u003cp\u003eWTH-Burner uses a 4020 fan for part cooling, just like the Voron Afterburner, and 3007 fan for hotend cooling. It's light weight and adapted internals make it perfect for \u003ca href=\"https:\/\/dfh.fm\/collections\/printers-for-ants\" title=\"printers for ants, at dfh.fm\" data-mce-href=\"https:\/\/dfh.fm\/collections\/printers-for-ants\" target=\"_blank\"\u003ePrinters for Ants\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eThe Kits are available in (mostly) black nickel coated stainless steel and hardened stainless steel. Of course, extra fasteners included, because accidents do happen.\u003c\/p\u003e\n\u003cp\u003eAll versions of the kit include the following:\u003c\/p\u003e\n\u003cp\u003eFans:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/dfh.fm\/products\/delta-electronics-asb0305hp-00cp4-5v-3007-axial-fan\" title=\"delta-electronics-asb0305hp-00cp4-5v-3007-axial-fan\" rel=\"noopener noreferrer\" data-mce-href=\"https:\/\/dfh.fm\/products\/delta-electronics-asb0305hp-00cp4-5v-3007-axial-fan\" target=\"_blank\"\u003eDelta Electronics ASB0305HP-00CP4\u003c\/a\u003e * 1\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/dfh.fm\/products\/4020-24v-dual-ball-blower-fan\" title=\"gdstime 4020-24v-dual-ball-blower-fan\" rel=\"noopener noreferrer\" data-mce-href=\"https:\/\/dfh.fm\/products\/4020-24v-dual-ball-blower-fan\" target=\"_blank\"\u003eGDStime 4020B24V2P2.54\u003c\/a\u003e * 1\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFasteners:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eM3x35 SHCS * 3\u003c\/li\u003e\n\u003cli\u003eM3x40 SHCS * 2\u003c\/li\u003e\n\u003cli\u003eM3x8 SHCS * 4\u003c\/li\u003e\n\u003cli\u003eM3x10 SHCS * 5\u003c\/li\u003e\n\u003cli\u003eM3x20 SHCS * 3\u003c\/li\u003e\n\u003cli\u003eM3x18 SHCS * 3\u003c\/li\u003e\n\u003cli\u003eM3x25 SHCS * 4\u003c\/li\u003e\n\u003cli\u003eM3x12 SHCS * 3\u003c\/li\u003e\n\u003cli\u003eM2.5x6 SHCS * 5\u003c\/li\u003e\n\u003cli\u003eM3x6 SHCS * 5\u003c\/li\u003e\n\u003cli\u003eM2x10 SHCS * 2\u003c\/li\u003e\n\u003cli\u003eM3x10 BHSC * 2\u003c\/li\u003e\n\u003cli\u003eM3x4 BHSC * 2\u003c\/li\u003e\n\u003cli\u003eM3 Hexnut * 3\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSuper Kit comes with everything you need:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca title=\"EC\\AS04\" href=\"https:\/\/dfh.fm\/products\/extruder-collet-ecas04\" target=\"_blank\" data-mce-href=\"https:\/\/dfh.fm\/products\/extruder-collet-ecas04\"\u003eECAS04\u003c\/a\u003e * 1\u003c\/li\u003e\n\u003cli\u003e\u003ca title=\"Collet Clip\" href=\"https:\/\/dfh.fm\/products\/collet-clip\" target=\"_blank\" data-mce-href=\"https:\/\/dfh.fm\/products\/collet-clip\"\u003eOrange Clip for ECAS04 * 1\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003ca title=\"PTFE Tube\" href=\"https:\/\/dfh.fm\/products\/ptfe-tube-1\" target=\"_blank\" data-mce-href=\"https:\/\/dfh.fm\/products\/ptfe-tube-1\"\u003e2mm ID 4mm OD PTFE Tube\u003c\/a\u003e * 300mm\u003c\/li\u003e\n\u003cli\u003e\n\u003ca title=\"FEP TUBE\" href=\"https:\/\/dfh.fm\/products\/transparent-fep-tube\" target=\"_blank\" data-mce-href=\"https:\/\/dfh.fm\/products\/transparent-fep-tube\"\u003e2.5mm ID 4mm OD FEP Tube\u003c\/a\u003e * 1.5m\u003c\/li\u003e\n\u003cli\u003e\u003ca title=\"ldo-36sth17-0354ahg dfh motor\" href=\"https:\/\/dfh.fm\/products\/ldo-36sth17-0354ahgdfh\" target=\"_blank\" data-mce-href=\"https:\/\/dfh.fm\/products\/ldo-36sth17-0354ahgdfh\"\u003eLDO LDO-36STH17-0354AHG(DFH) Motor\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/dfh.fm\/products\/rnc-coated-extruder-components-kit-by-runice\" target=\"_blank\" title=\"rnc-coated-extruder-components-kit-by-runice\" rel=\"noopener\"\u003eRNC Coated BMG Clone Components Kit by Runice\u003c\/a\u003e * 1\u003c\/li\u003e\n\u003cli\u003eRGBW LED * 3\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eMore information on the project may be found in the GitHub repo, \u003ca href=\"https:\/\/github.com\/kevinakasam\/WTH-Burner\" title=\"github link to WTH-Burner\" rel=\"noopener noreferrer\" data-mce-href=\"https:\/\/github.com\/kevinakasam\/WTH-Burner\" target=\"_blank\"\u003ehere\u003c\/a\u003e.\u003c\/p\u003e","brand":"dfh.fm","offers":[{"title":"Standard \/ Stainless Steel","offer_id":44802317615326,"sku":"","price":24.99,"currency_code":"USD","in_stock":true},{"title":"Standard \/ Black Nickel Coated Stainless Steel","offer_id":44802317648094,"sku":"","price":26.99,"currency_code":"USD","in_stock":true},{"title":"Super \/ Stainless Steel","offer_id":44808391196894,"sku":"","price":77.99,"currency_code":"USD","in_stock":true},{"title":"Super \/ Black Nickel Coated Stainless Steel","offer_id":44808391229662,"sku":"","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/WTH_Burner-1.jpg?v=1708569228"},{"product_id":"phaetus-next-g-ceramic-heating-kit","title":"Phaetus neXt G Ceramic Heating Kit","description":"\u003cp\u003e\u003cstrong\u003eOEM Phaetus\/DropEffect ceramic heating kit for neXt G hotends.\u003c\/strong\u003e Use it to replace the ceramic heater assembly on a neXt G or neXtG Fiber hotend without replacing the whole toolhead.\u003c\/p\u003e\n\u003ch3\u003eWhy use the original heating kit\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eMatches the Phaetus\/DropEffect neXt G hotend family instead of a generic cartridge heater.\u003c\/li\u003e\n  \u003cli\u003eRestores the hotend's ceramic heater setup for high-flow printing and stable temperature control.\u003c\/li\u003e\n  \u003cli\u003eBest fit when you already have the neXt G hardware and only the heater assembly needs replacement.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eBrand: \u003cstrong\u003ePhaetus \/ DropEffect\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eProduct: \u003cstrong\u003eCeramic Heating Kit\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eCompatibility: \u003cstrong\u003eneXt G \/ neXtG Fiber\u003c\/strong\u003e hotends\u003c\/li\u003e\n  \u003cli\u003eVoltage: \u003cstrong\u003e24V\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eManufacturer barcode visible on packaging: \u003cstrong\u003e6973090164577\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFits and pairs with\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eReplacement heater assembly for the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-dropeffect-next-g-extreme-gradient-hotend-104nt-version\"\u003ePhaetus DropEffect neXt G Extreme Gradient Hotend 104NT Version\u003c\/a\u003e.\u003c\/li\u003e\n  \u003cli\u003ePairs with the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heat-block\"\u003ePhaetus neXt G Heat Block\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heatbreak-kit\"\u003ePhaetus neXt G Heatbreak Kit\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heatsink\"\u003ePhaetus neXt G Heatsink\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-pt1000-brass-screw\"\u003ePhaetus neXt G PT1000 Brass Screw\u003c\/a\u003e, and \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-socks\"\u003ePhaetus neXt G Silicone Sock\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eNot a complete hotend.\u003c\/li\u003e\n  \u003cli\u003eNot a universal heater cartridge for unrelated hotend families.\u003c\/li\u003e\n  \u003cli\u003eReuse your existing neXt G hardware unless you are also replacing damaged blocks, sensors, socks, or heatbreak parts.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus\/DropEffect","offers":[{"title":"Default Title","offer_id":45072459202782,"sku":"5175061356","price":6.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/Phaetus_next-g-ceramic-heating-kit.jpg?v=1712376831"},{"product_id":"phaetus-next-g-heatbreak-kit","title":"Phaetus neXt G Heatbreak Kit","description":"\u003cp\u003e\u003cstrong\u003eOriginal Phaetus\/DropEffect replacement heatbreak for the neXt G hotend family.\u003c\/strong\u003e Use this kit to replace a damaged or worn neXt G heatbreak without replacing the whole hotend assembly.\u003c\/p\u003e\n\u003ch3\u003eWhy replace just the heatbreak?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eKeeps a neXt G hotend in service after heatbreak wear, nozzle crash damage, or a rebuild.\u003c\/li\u003e\n\u003cli\u003eMatches the Phaetus\/DropEffect neXt G hotend architecture, including the rigid heater-block-to-heatsink stack that protects the heatbreak during nozzle changes and bed-crash events.\u003c\/li\u003e\n\u003cli\u003eUseful spare for high-temperature or abrasive-material setups where the hotend sees hard service.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eBrand \/ family: \u003cstrong\u003ePhaetus \/ DropEffect neXt G\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003ePart type: \u003cstrong\u003ereplacement heatbreak kit\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eCompatibility: neXt G \/ neXtG hotends from DropEffect; check your hotend version before ordering.\u003c\/li\u003e\n\u003cli\u003eHotend context: neXt G hotends use V6-style nozzles and a Dragon-style footprint for broad mount compatibility.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFits with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-dropeffect-next-g-extreme-gradient-hotend-104nt-version\"\u003ePhaetus DropEffect neXt G Extreme Gradient Hotend 104NT Version\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-ceramic-heating-kit\"\u003ePhaetus neXt G Ceramic Heating Kit\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heat-block\"\u003ePhaetus neXt G Heat Block\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heatsink\"\u003ePhaetus neXt G Heatsink\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNot a complete hotend.\u003c\/li\u003e\n\u003cli\u003eNot a universal V6 or Dragon heatbreak; buy it for a Phaetus\/DropEffect neXt G build or repair.\u003c\/li\u003e\n\u003cli\u003eIf you are replacing a Fiber-version heatbreak, confirm your exact hotend version before checkout.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus\/DropEffect","offers":[{"title":"Default Title","offer_id":45072487284958,"sku":"5283229415","price":13.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/phaetus-next-g-heatbreak-kit-asdhg.jpg?v=1712377449"},{"product_id":"phaetus-next-g-heatsink","title":"Phaetus neXt G Heatsink","description":"\u003cp\u003e\u003cstrong\u003eOEM replacement cold-side heatsink for the DropEffect\/Phaetus neXt G family.\u003c\/strong\u003e Use this when the original neXt G heatsink is damaged, missing, or being rebuilt as part of hotend service.\u003c\/p\u003e\n\u003ch3\u003eWhy this part\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eDirect replacement heatsink for \u003cstrong\u003eDropEffect neXtG \/ neXtG Fiber\u003c\/strong\u003e hotends.\u003c\/li\u003e\n  \u003cli\u003eMatches the neXt G hotend architecture, where the kinematic coupling limits heat transfer into the heatsink while keeping the heater block rigid.\u003c\/li\u003e\n  \u003cli\u003eSmall spare part to keep on hand if you service hotends often or are rebuilding a toolhead after a crash.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eBrand \/ family: \u003cstrong\u003ePhaetus DropEffect neXt G\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003ePart: \u003cstrong\u003eheatsink \/ cold-side replacement body\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eManufacturer item number: \u003cstrong\u003ePH-6973090164638\u003c\/strong\u003e\n\u003c\/li\u003e\n  \u003cli\u003eCompatible models: \u003cstrong\u003eneXtG\u003c\/strong\u003e and \u003cstrong\u003eneXtG Fiber\u003c\/strong\u003e hotends\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eUse with the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-dropeffect-next-g-extreme-gradient-hotend-104nt-version\"\u003ePhaetus DropEffect neXt G hotend\u003c\/a\u003e and other neXt G-family service parts such as the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heatbreak-kit\"\u003eneXt G heatbreak kit\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heat-block\"\u003eneXt G heat block\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-ceramic-heating-kit\"\u003eneXt G ceramic heating kit\u003c\/a\u003e, and \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-socks\"\u003eneXt G silicone sock\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eNot included\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eNot a complete hotend.\u003c\/li\u003e\n  \u003cli\u003eDoes not include the heatbreak, heater block, ceramic heater, thermistor, nozzle, or silicone sock.\u003c\/li\u003e\n  \u003cli\u003eVerify you are servicing a neXt G \/ neXtG Fiber hotend before ordering; this is not a generic V6 or Dragon heatsink.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus\/DropEffect","offers":[{"title":"Default Title","offer_id":45072509239518,"sku":null,"price":9.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/IMG_6615.jpg?v=1712377738"},{"product_id":"phaetus-next-g-heat-block","title":"Phaetus neXt G Heat Block","description":"\u003cp\u003e\u003cstrong\u003eOEM replacement heater block for the Phaetus\/DropEffect neXt G hotend family.\u003c\/strong\u003e Use this block to rebuild a neXt G or neXtG Fiber hotend after stripped nozzle threads, crash damage, or a hot-side service tear-down.\u003c\/p\u003e\n\u003ch3\u003eWhy replace the block instead of the whole hotend?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRestores the hot side while keeping the rest of your neXt G assembly in service.\u003c\/li\u003e\n\u003cli\u003eMatches the neXt G rigid kinematic-coupling architecture, where the heater block is held solidly to protect the heatbreak during nozzle changes and print strikes.\u003c\/li\u003e\n\u003cli\u003eWorks with the neXt G family design that uses V6-style nozzles and a Dragon-style mounting footprint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eBrand \/ family: \u003cstrong\u003ePhaetus \/ DropEffect neXt G\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003ePart type: \u003cstrong\u003ereplacement heater block \/ heat block\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eManufacturer item number: \u003cstrong\u003ePH-6973090164614\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eCompatibility: \u003cstrong\u003eneXtG\u003c\/strong\u003e and \u003cstrong\u003eneXtG Fiber\u003c\/strong\u003e hotends\u003c\/li\u003e\n\u003cli\u003eHotend context: neXt G hotends use a ceramic heating plate, V6 nozzle interface, and Dragon-style footprint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eUse with the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-dropeffect-next-g-extreme-gradient-hotend-104nt-version\"\u003ePhaetus DropEffect neXt G hotend\u003c\/a\u003e and neXt G service parts including the \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heatbreak-kit\"\u003eneXt G heatbreak kit\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-heatsink\"\u003eneXt G heatsink\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-ceramic-heating-kit\"\u003eneXt G ceramic heating kit\u003c\/a\u003e, \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-pt1000-brass-screw\"\u003ePT1000 brass screw\u003c\/a\u003e, and \u003ca href=\"https:\/\/dfh.fm\/products\/phaetus-next-g-socks\"\u003eneXt G silicone sock\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eWhat it is not\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNot a complete hotend.\u003c\/li\u003e\n\u003cli\u003eDoes not include the heatbreak, heatsink, ceramic heater, thermistor, nozzle, or silicone sock.\u003c\/li\u003e\n\u003cli\u003eNot a generic V6 or Dragon heater block; buy it for a Phaetus\/DropEffect neXt G or neXtG Fiber rebuild.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Phaetus\/DropEffect","offers":[{"title":"Default Title","offer_id":45072520282334,"sku":"7815788297","price":17.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0556\/9767\/0313\/files\/IMG_6616.jpg?v=1712378303"}],"url":"https:\/\/formosissima.myshopify.com\/collections\/hotends.oembed","provider":"dfh.fm","version":"1.0","type":"link"}